JBL CRT Television SCS110 User Manual

TM  
SCS110  
simple  
set-up guide  
thank you  
for choosing JBL. For over 50 years, JBL  
has been involved in every aspect of musical and film recording  
and reproduction, from live performances to monitoring the  
recordings you play in your home, car, or office.  
Were confident that the JBL system you have chosen  
will provide every note of enjoyment that you expected –  
and that when you think about purchasing additional audio  
equipment for your home, car, or office, you will once again  
choose JBL.  
Please take a moment to complete the enclosed profile card.  
It enables us to keep you posted on our latest advancements,  
and helps us to better understand our customers and build  
products that meet your needs and expectations.  
JBL Consumer Products  
 
one.  
Satellites  
Speaker Placement  
Subwoofer  
0-2 ft.  
Surround Speakers  
5
– 6 ft.  
Mounting Options  
Satellites  
On the wall. Optional bracket.  
Part No. SFX10BKT, or  
On optional stands.  
Part No. FS10/ 20.  
On shelves.  
SFX10BKTWHT (white).  
FS10/ 20WHT (white).  
Surrounds  
On optional stands.  
On shelves.  
Wall-mounted. Brackets and  
hardware included.  
 
two.  
Speaker Connections  
Connection Tips  
identically: (+) on the speaker  
to (+) on the amplifier and (–)  
on the speaker to (–) on the  
amplifier. Wiring “out of  
phase” results in thin sound,  
weak bass and a poor stereo  
image.  
Separate and strip the ends of  
the speaker wire as shown.  
Speakers and electronics ter-  
minals have corresponding (+)  
and (–) terminals. It is impor-  
tant to connect both speakers  
For satellites, thread speaker  
wire through the hole in the  
bottom of the speaker, then  
feed it through the recessed  
wire channel.  
Left Front  
sat10  
Center  
Speaker  
Right Front  
sat10  
+
+
+
Subwoofer  
+
+
Left  
Right  
Output to Satellite  
Input from Amplifier  
Left Right  
+
+
Receiver  
Center  
Front  
Rear  
+
+
+
+
+
Left  
Surround  
Right  
Surround  
L
R
L
R
+
+
 
three.  
Testing  
Finally. Take a “test drivewith some favorite music or movies.  
1. With the receiver/ amplifier  
still turned off, confirm that  
its volume control is turned  
all the way down. Next,  
center the balance control. If  
the receiver/ amplifier has an  
A/ B speaker switch, set it to  
correspond to the speaker  
terminals connected to the  
SCS110 system.  
2. Now, turn on your receiver/  
amplifier and select a music  
source such as a CD player,  
cassette deck or FM tuner.  
3. Turn up the volume control  
slowly until you hear sound  
from the speakers.  
4. Rotate the balance control  
all the way to the left. Sound  
should come only from the  
left speaker. If the sound  
comes from the right speaker  
with the balance control to  
the left, the speaker wires  
have been reversed during  
hook-up. Turn the receiver/  
amplifier “off” and switch  
both sets of speaker wires.  
Dolby Pro Logic*-equipped  
devices (AV Receivers,  
volume of all the speakers in  
a surround sound system.  
Refer to the instructions  
accompanying your compo-  
nent for selecting the test  
tone mode and using it to  
balance speaker levels in your  
home theater.  
Surround Sound processors  
or decoders, TVs or other  
sources) include a “test tone”  
you can use to balance the  
Troubleshooting  
If there is no sound from  
any of the speakers, check  
the following:  
Receiver/ amplifier is on and  
a source is playing.  
If the system plays at low  
volumes but shuts off as  
volume is increased, check  
the following:  
Check all wires and con-  
nections between receiver/  
amplifier and speakers.  
If there is low bass output,  
check the following:  
Make sure the polarity  
(+ and –) of the left and  
right “Speaker Inputs” are  
connected properly.  
Review proper operation of  
your receiver/ amplifier.  
Make sure all wires are con-  
nected. Make sure none of the  
speaker wires are frayed, cut,  
or punctured.  
• If more than one pair of  
main speakers is being used,  
check the minimum impedance Make sure all wires are con-  
requirements of your receiver/  
amplifier.  
If there is no sound from  
the surround speakers, check  
the following:  
Check all wires and con-  
nections between receiver/  
amplifier and speakers.  
If there is no sound coming  
from one speaker, check the  
following:  
Check the “Balance” control  
on your receiver/ amplifier.  
Check all wires and con-  
nections between receiver/  
amplifier and speakers.  
Make sure all wires are con-  
nected. Make sure none of the  
speaker wires are frayed, cut,  
or punctured.  
nected. Make sure none of the  
speaker wires are frayed, cut,  
or punctured.  
Review proper operation of  
your receiver/ amplifier and its  
surround sound features.  
 
sat10  
bass10  
Specifications  
SCS110 System  
Power Handling  
10 – 80 watts  
Power Handling  
10 – 120 watts  
Frequency Response  
150Hz – 20kHz (±3dB)  
Frequency Response  
40Hz – 150Hz (±3dB)  
Power Handling  
10 – 120 watts  
Impedance  
8 ohms nominal  
Impedance  
8 ohms nominal  
Frequency Response  
40Hz – 20kHz (±3dB)  
Sensitivity  
Sensitivity  
88dB @ 1 watt/ 1 meter  
88dB @ 1 watt/ 1 meter  
Crossover Frequency  
3.5kHz (midrange to tweeter)  
Crossover Frequency  
150Hz (subwoofer to satellite)  
Accessories such as the  
optional stands and brackets  
are available through your JBL  
dealer. For a dealer in the USA  
call 1-800-336-4JBL.  
Tweeter  
One 3/ 4" titanium composite  
dome, video-shielded  
Bass  
Two 5-1/ 4" woofers  
Triple chamber band-pass  
subwoofer  
Midrange  
One 3-1/ 2" neodymium  
driver, video-shielded  
Dimensions (HxWxD)  
14-3/ 4 x 8-1/ 2 x 19 inches  
375 x 216 x 465mm  
Refinements may be made on  
occasion to existing products  
without notice, but will always  
meet or exceed original speci-  
fications unless otherwise  
stated.  
Dimensions (HxWxD)  
6-1/ 2 x 3-3/ 4 x 4-1/ 4 inches  
165 x 95 x 108mm  
Weight  
28 lbs/ 12.7 kg  
Weight  
1.5 lbs/ .7 kg  
Notice to Purchaser: JBL  
assumes no responsibility or  
liability for injuries or property  
damage – direct, indirect, or  
consequential – resulting from  
the improper installation of  
these loudspeakers.  
sat10 Surround  
Speakers  
Declaration of Conformity  
Recommended Power  
10 – 70 watts  
Impedance  
8 ohms nominal  
We, JBL Europe A/S  
Kongevejen 194B  
DK-3460 Birkerød  
DENMARK  
Sensitivity  
90dB @ 1 watt/ 1 meter  
declare in own responsibility, that the products described  
in this owner’s manual are in compliance with technical  
standards:  
Frequency Response  
100Hz – 15kHz (±3dB)  
EN 50 081-1/1992  
EN 50 082-1/3.1995  
Dimensions (HxWxD)  
6-1/ 2 x 3-3/ 4 x 4-1/ 4 inches  
165 x 95 x 108mm  
Weight  
1.5 lbs/ .7 kg  
Steen Michaelsen  
JBL Europe A/S  
Birkerød. DENMARK. 7/96  
JBL Consumer Products  
80 Crossways Park West, Woodbury, NY 11797  
8500 Balboa Boulevard, Northridge, CA 91329  
1-800-336-4JBL (4525) (USA only)  
1996 JBL, Incorporated. JBL and Simply Cinema are registered trademarks of JBL, Incorporated.  
©
*Trademark of Dolby Laboratories.  
Printed in USA 8/ 96  
Part No. SCS110OM  
A Harman International Company  
 

Insignia Cable Box NS 32DD310NA15 User Manual
Insignia Portable CD Player NS BCDCAS1 User Manual
InSinkErator Indoor Furnishings H778 User Manual
Intel Computer Hardware S3200SH User Manual
Invacare Wheelchair E1161 User Manual
Jenn Air Cooktop W10526080A User Manual
JVC DVD Player SP XSV70 User Manual
Kingston Technology Network Router 480 15FUM 001A00 User Manual
Kompernass Hair Dryer KH 1801 User Manual
Kompernass Portable DVD Player KH 2370 User Manual