PAS 7,2V
Operation and Safety Notes
Operation and Safety Notes ........................................................................................Page 5
Table of Content
Before reading, unfold the page containing the illustrations
and familiarise yourself with all functions of the device.
The following icons/symbols are used in this instruction manual:
Direct current
(Type of current and voltage)
Read instruction manual!
Observe caution and safety notes!
Newtonmeter (Torque)
Nm
n0
Rated idle running speed
Protection category II
Caution – electric shock!
Dangerous electric current –
danger to life!
Amp-hours (Battery capacity)
Proper procedure and handling.
Ah
V~
Voltage
Introduction
For your safety...................................................................................................... Page
Intended Use......................................................................................................... Page
Equipment............................................................................................................. Page
Scope of Supply .................................................................................................... Page
Technical Data ...................................................................................................... Page
6
6
6
6
6
Safety
Safety Information Specific to this Device ............................................................ Page
7
Initial Use
Charging the Battery Pack..................................................................................... Page
Inserting and Removing the Rechargeable Battery Pack from the Device.............. Page
Torque Pre-selection ............................................................................................ Page
Angular Position.................................................................................................... Page
Changing the Tool ................................................................................................ Page
Switching on/off................................................................................................... Page
Setting the Speed.................................................................................................. Page
Reversing the Direction of Rotation ....................................................................... Page
Tips and Tricks...................................................................................................... Page
7
8
8
8
8
8
8
9
9
Maintenance and Cleaning............................................................................. Page
9
9
Disposal................................................................................................................. Page
Information
Servicing............................................................................................................... Page
9
Manufacturer’s declaration of conformity.............................................................. Page 10
GB/IE
5
Introduction
Rechargeable Cordless Screwdriver
PAS7,2 V
L Scope of Supply
1 rechargeable cordless screwdriver
with rechargeable battery pack
1 quick charging device
3 screw bits (hexagonal shaft/6,35mm)
1 carrying case
L Introduction
L For your safety
1 “rechargeable battery pack” ordering card
1 set of operating instructions
Please make sure you familiarise yourself 1 “General Safety Instructions” booklet
fully with the way the device works before
you use it for the first time and that you
1 “Guarantee and Service” booklet
understand how to handle electrical power tools cor-
rectly. Further details can be found in the operating
instructions. In addition to the above, you must also
observe the general safety advice contained in the
L Technical Data
Rechargeable Screwdriver Parkside PAS 7,2V:
accompanying booklet. Keep these instructions in a safe Rated voltage:
place. If you pass the device on to anyone else, please Rated speed:
7,2VDC
n0 0-500min-1
hexagonal/6,35mm
16
ensure that you also pass on all the documentation.
Tool holder:
Torque levels:
Max. torque:
9Nm
L Intended Use
Sound pressure level: < 70dB (A)
Noise level:
Vibration value:
86dB (A)
This device is intended to be used for screwing into
wood, plastic and metal. It should only be used as
described and for the stated fields of application.
Any other use or modification to this device is deemed
contrary to its intended use and harbours a consid-
erable risk of accidents. The manufacturer accepts
no liability for damage caused through improper use
of this device.
< 2.5m/s2
Rechargeable Battery Pack PAS 7,2V-1:
Rated voltage:
7,2VDC
Nominal capacity:
Energy content:
1,3Ah
9,4Wh
Battery Fast Charging Device PAS 7,2V-2:
Not intended for professional use.
Primary:
Nominal voltage:
Power consumption:
230V~50Hz
30W
L Equipment
Secondary:
Q
Tool holder (hexagonal/6,35mm)
Torque pre-selector
Switch for angular position
Direction of rotation switch/lock
Bit storage
Rechargeable battery pack
Button for releasing the battery
ON/OFF switch/speed regulation
Nominal voltage:
Charging current:
Charging period:
Protection class:
7,2VDC
2000mA
ca. 60min.
II/
W
E
R
T
Y
U
I
O
Fast charging device
Green charging control LED
P
{
Red charging control LED
6
GB/IE
Safety/Initial Use
Y
L Safety
explosion! Handle the rechargeable battery pack
carefully and protect it against knocks and jolts!
J Warning! If you should come into contact with
Y
Safety Information Specific
to this Device
acid from the rechargeable battery pack , the
acid must be washed off thoroughly with water
without delay. If acid should enter your eyes, rinse
it out immediately with water and seek medical
advice immediately.
J
Please keep children away from this
device. The screwdriver should be
stored in a dry, closed room to which
children do not have access.
J
Caution! Detection devices should be used to deter-
mine the position of supply lines so that you do not
damage any electrical wiring or gas or water pipes.
Avoid the Danger of Death
by Electric Shock!
Stay Safe!
J Always disconnect the mains plug before cleaning
O
Avoid the Danger of Injury and Fire and
Harmful Effects on Health!
or maintaining the fast charging device or
Y
rechargeable battery pack
.
Y
J Never charge the battery pack if the surround-
J
Damaged devices, mains leads or
mains plugs may cause death by
electric shock. You should therefore
ing temperature is below 10 °C or above 40 °C.
O
J The ventilation holes of the fast charging device
should never become blocked.
check the condition of the screwdriver, the fast
J Whenever the screwdriver is being adjusted,
transported or stored, please move the direction
O
charging device , mains lead, mains plug and
Y
R
rechargeable battery pack at regular intervals.
of rotation switch to the middle position (lock)
J Any parts that are damaged must not be used. In
case of danger, disconnect the mains plug from
the socket immediately.
in order to prevent the screwdriver switching on
accidentally.
J High torques occur when hard surfaces are being
screwed into. You should therefore hold the
screwdriver very tight in order to avoid injury!
-
-
The screwdriver should never be opened.
All repairs or parts replacements may only be
carried out by the service centre or a special-
ist electrician.
O
J Please protect the fast charging device
,
L Initial Use
Y
rechargeable battery pack and the screwdriver
itself against moisture.
O
J Warning! Only the fast charging device
/
L Charging the Battery Pack
Y
rechargeable battery pack supplied may be used.
(Illustration B)
Y
J Warning! The rechargeable battery pack
Y
must not be short-circuited, otherwise overheating, Notice: A rechargeable battery pack that is new
Y
fire or bursting of the rechargeable battery pack
or has not been used for a long time has to be
may result. For this reason:
charged up before initial/renewed use.
- do NOT connect cables to the poles of the battery
Y
Y
The rechargeable battery pack reaches its full
pack
.
- ensure that the rechargeable battery connectors
cannot be short-circuited by other metal parts
(nails, screws etc.).
capacity after approx. 3-5 charging cycles.
1. Insert the mains plug into the socket. The green
Y
P
J Caution! The rechargeable battery pack must
charging control LED lights up.
never be thrown into a fire or water. Danger of
GB/IE
7
Initial Use
Y
2. Place the battery pack in the fast charging
j Select a low level for small screws and soft ma-
terials.
O
P
device . The green charging control LED ex-
{
tinquishes and the red charging control LED
,
j Select a high level for large screws, hard materials
now glowing, indicates the start of the charging
and when loosening screws.
{
process. The red charging control LED extin-
j If level 16 is selected, the clutch does not disconnect
the drive. The drive chain is locked in place. Select
this level if you require maximum rotary force.
Y
guishes as soon as the battery pack is fully
charged.
P
3. The green charging control LED indicates that
charging is complete and the rechargeable battery
Y
pack is ready for use.
L Angular Position (Illustration A)
4. Disconnect the mains plug of the fast charging
O
E
device from the socket.
j Press and hold the angular position switch
Y
Remove the rechargeable battery pack
.
(see illustration A).
j Move the device into the angular position
(no intermediate setting).
E
Y
j A rechargeable battery pack must never be
charged up a second time immediately after the
fast charging procedure. Otherwise there is a
j Release the angular position switch
.
Check whether the screwdriver has locked in
place in the angular position.
Y
danger that the rechargeable battery pack will
be overcharged, thus reducing the lifetime of the
Y
rechargeable battery pack and the fast charging
O
device
.
L Changing the Tool
j The charging device should be switched off for
at least 15 minutes between charging.
Please remove the mains plug.
Inserting
j Insert the bit into the tool holder
Q
.
Removing
j Remove the bit from the tool holder
Q
L Inserting and Removing the
Rechargeable Battery Pack
from the Device
.
L Switching on/off
Inserting the Rechargeable Battery Pack:
R
R
Notice: If the rotation direction switch is located in
I
the central/neutral position, the ON/OFF switch is
blocked. Therefore select a rotation direction before
switching on, in that the rotation direction switch
j Please move the direction of rotation switch
to the “lock” position and allow the rechargeable
Y
battery pack to lock into place in the handle.
R
Removing the Rechargeable Battery Pack:
is pushed through completely
U
j Press the side release buttons simultaneously
j To switch the screwdriver on, press the ON/OFF
Y
I
and remove the rechargeable battery pack
.
switch and keep it pressed.
j To switch the screwdriver off, release the ON/OFF
I
switch
.
L Torque Pre-selection
The rotary force can be adjusted by means of the
torque pre-selector . The torque levels go up to
L Setting the Speed
W
I
The ON/OFF switch has a variable speed control.
approximately 9Nm.
Once the rotary force that has been set (markings
1-15) is reached, the clutch disconnects the drive.
Increasing the Speed
j Increase the pressure on the ON/OFF switch
I
.
8
GB/IE
Initial Use/Maintenance and Cleaning/Disposal/Information
Reducing the Speed
j Reduce the pressure on the ON/OFF switch
L Disposal
I
.
The packaging is made entirely of recyclable
materials, which you may dispose of at local
recycling facilities.
L Reversing the Direction of Rotation
R
Notice: If the rotation direction switch is located
in the central/neutral position, the ON/OFF switch
Do not dispose of electrical appliances
in household waste.
I
is blocked. The rotation direction is only to be
switched when the appliance is at standstill.
j Reverse the direction of rotation by pressing the
In accordance with European Directive 2002/96/EC
on used electrical and electronic appliances and its
implementation in national law, used power tools
must be collected separately and recycled in an eco-
logically compatible manner.
R
direction of rotation switch to the right or left.
L Tips and Tricks
Faulty or used rechargeable batteries must be
recycled in accordance with Directive 91/157/EEC.
Please refer to the special safety advice in relation
By simply changing from the angled to the straight
position you can work effortlessly in any position
(see illustration C).
O
Y
to the charger and battery pack
.
Particularly when assembling furniture you can
Return the appliance with integrated rechargeable
reach difficult-to-access places more easily with the battery via the available collection facilities.
slender device (see illustration D).
Information on options for disposing of electrical ap-
When screwing into wood, metal and other
materials, please note the following:
j Before operation, check that the scewdriver bit is
sitting properly, i.e. is correctly centred in the tool
Q
pliances after their useful life can be obtained from
your local or city council.
holding fixture
.
L Information
j Screw-bits are marked with their size and type. If
you are unsure, always test first to see if the bit
sits firmly and without free play in the tool hold-
Q
L Servicing
ing fixture
.
The service centre for your country is shown in the
guarantee documentation.
Torque: Small screws and bits in particular may be
damaged if the selected torque and/or speed of the
device is too high.
L Maintenance and Cleaning
The rechargeable screwdriver is maintenance-free.
j The screwdriver should be cleaned regularly,
immediately upon completion of the work.
j A dry cloth should be used to clean the housing;
under no circumstances should petrol, solvent or
other cleaning agents be used.
GB/IE
9
Information
L Manufacturer’s declaration
of conformity
We, Kompernaß GmbH, Burgstr. 21, D-44867 Bochum,
Germany, declare that this product complies with the
following EU directives:
EG Low Voltage Directive (73/23/EEC)
Electromagnetic compatibility
(89/336/EEC), (92/31/EEC)
Applicable harmonised standards:
EN 60335-1:2002+A1+A11
EN 60335-2-29
EN 50366
EN 55014-1:2000+A1+A2
EN 55014-2:1997+A1
EN 61000-3-2
EN 61000-3-3:1995+A1
Description of the product:
Rechargeable Cordless Screwdriver PAS 7,2V
Bochum, 31.10.2006
Hans Kompernaß
- Managing Director -
We reserve the right to make technical modifications in the course
of further development.
10 GB/IE
11
12
|