Kyocera Cell Phone KX16 User Manual

 
Although the SAR is determined at the highest  
certified power level, the actual SAR level of the  
phone while operating can be well below the  
maximum value. This is because the phone is  
designed to operate at multiple power levels so as  
to use only the power required to reach the network.  
In general, the closer you are to a wireless base  
station antenna, the lower the power output.  
Optimize your phone’s performance  
Use the guidelines on page 2 to learn how to  
optimize the performance and life of your phone  
and battery.  
Air bags  
If you have an air bag, DO NOT place installed or  
portable phone equipment or other objects over the  
air bag or in the air bag deployment area. If  
equipment is not properly installed, you and your  
passengers risk serious injury.  
Before a phone model is available for sale to the  
public, it must be tested and certified to the FCC  
that it does not exceed the limit established by the  
government-adopted requirement for safe  
exposure. The tests are performed in positions and  
locations (e.g., at the ear and worn on the body) as  
required by the FCC for each model.  
Medical devices  
Pacemakers—Warning to pacemaker wearers:  
Wireless phones, when in the ‘on’ position, have  
been shown to interfere with pacemakers. The  
phone should be kept at least six (6) inches away  
from the pacemaker to reduce risk.  
While there may be differences between the SAR  
levels of various phones and at various positions,  
they all meet the government requirement for  
safe exposure.  
The Health Industry Manufacturers Association  
and the wireless technology research community  
recommend that you follow these guidelines to  
minimize the potential for interference.  
The FCC has granted an Equipment Authorization  
for this model phone with all reported SAR levels  
evaluated as in compliance with the FCC RF  
emission guidelines. SAR information on this  
model phone is on file with the FCC and can be  
found under the Display Grant section  
Always keep the phone at least six inches  
(15 centimeters) away from your pacemaker  
when the phone is turned on.  
Do not carry your phone near your heart.  
Use the ear opposite the pacemaker.  
http://www.fcc.gov/oet/fccid after searching on the  
FCC ID: OVFKWC-KX16.  
If you have any reason to suspect that  
interference is taking place, turn off your phone  
immediately.  
Additional information on SAR can be found on the  
Cellular Telecommunications and Internet  
Association (CTIA) web-site at  
Hearing aids—Some digital wireless phones may  
interfere with hearing aids. In the event of such  
interference, you may want to consult your service  
provider or call the customer service line to discuss  
alternatives.  
* In the United States and Canada, the SAR limit  
for mobile phones used by the public is  
1.6 watts/kg (W/kg) averaged over one gram of  
tissue. The standard incorporates a substantial  
margin of safety to give additional protection for the  
public and to account for any variations in  
measurements.  
Other medical devices—If you use any other personal  
medical device, consult the manufacturer of the  
device to determine if it is adequately shielded  
from external RF energy. Your physician may be  
able to help you obtain this information.  
Caution  
In health care facilities—Turn your phone off in health  
care facilities when instructed. Hospitals and  
health care facilities may be using equipment that  
is sensitive to external RF energy.  
The user is cautioned that changes or  
modifications not expressly approved by the party  
responsible for compliance could void the warranty  
and user’s authority to operate the equipment.  
User Guide for the Kyocera Candid KX16 Phone  
iii  
 
Potentially unsafe areas  
Posted facilities—Turn your phone off in any facility  
when posted notices require you to do so.  
Resetting the phone  
If the screen seems frozen and the keypad does  
not respond to keypresses, reset the phone by  
completing the following steps:  
Aircraft—FCC regulations prohibit using your phone  
on a plane that is in the air. Turn your phone off or  
switch it to Airplane Mode before boarding aircraft.  
1. Remove the battery door.  
2. Remove and replace the battery.  
If the problem persists, return the phone to the  
dealer for service.  
Vehicles—RF signals may affect improperly installed  
or inadequately shielded electronic systems in  
motor vehicles. Check with the manufacturer of the  
device to determine if it is adequately shielded  
from external RF energy. Your physician may be  
able to help you obtain this information.  
Accessories  
Use only Kyocera-approved accessories with  
Kyocera phones. Use of any unauthorized  
accessories may be dangerous and will invalidate  
the phone warranty if said accessories cause  
damage or a defect to the phone.  
Blasting areas—Turn off your phone where blasting  
is in progress. Observe restrictions, and follow any  
regulations or rules.  
To shop online for phone accessories, visit  
Potentially explosive atmospheres—Turn off your  
phone when you are in any area with a potentially  
explosive atmosphere. Obey all signs and  
instructions. Sparks in such areas could cause an  
explosion or fire, resulting in bodily injury or death.  
To order by phone, call (800) 349-4188  
(U.S.A. only) or (858) 882-1410.  
Radio Frequency (RF) energy  
Areas with a potentially explosive atmosphere are  
often, but not always, clearly marked. They include:  
Your telephone is a radio transmitter and receiver.  
When it is on, it receives and sends out RF energy.  
Your service provider’s network controls the power  
of the RF signal. This power level can range from  
0.006 to 0.6 watts.  
fueling areas such as gas stations  
below deck on boats  
transfer or storage facilities for fuel or chemicals  
In August 1996, the U.S. Federal Communications  
Commission (FCC) adopted RF exposure  
guidelines with safety levels for hand-held wireless  
phones. These guidelines are consistent with the  
safety standards previously set by both U.S. and  
international standards bodies in the following  
reports:  
vehicles using liquefied petroleum gas, such as  
propane or butane  
areas where the air contains chemicals or  
particles such as grain, dust, or metal powders  
any other area where you would normally be  
advised to turn off your vehicle engine  
ANSI C95.1 (American National Standards  
Institute, 1992)  
Use with care  
Use only in normal position (to ear). Avoid  
dropping, hitting, bending, or sitting on the phone.  
NCRP Report 86 (National Council on  
Radiation Protection and Measurements,  
1986)  
Keep phone dry  
If the phone gets wet, turn the power off  
immediately and contact your dealer. Water  
damage may not be covered under warranty.  
ICNIRP (International Commission on Non-  
Ionizing Radiation Protection, 1996)  
Your phone complies with the standards set by  
these reports and the FCC guidelines.  
iv  
 
E911 mandates  
Where service is available, this handset complies  
with the Phase I and Phase II E911 Mandates  
issued by the FCC.  
Battery and charger specifications  
Charger  
Input  
Output  
TXACA10004  
TXTVL10063  
120 VAC, 60 Hz, 7 W 5.2VDC, 400 mA  
100 - 240 VAC,  
50 / 60 Hz, 200 mA  
4.2VDC, 600 mA  
Standard Battery  
3.7V, 900 mAh  
Extended Battery  
3.7V, 1800 mAh  
093 453 037  
Kyocera Wireless Corp.  
10300 Campus Point Drive, San Diego, CA 92121  
U.S.A.  
To purchase accessories, visit  
User Guide for the Kyocera Candid KX16 Phone  
v
 
CONTENTS  
1
Getting Started. . . . . . . . . . . . . . . . . . . . . . 1  
Installing the battery . . . . . . . . . . . . . . . . . . . . . . 1  
Getting to know your phone . . . . . . . . . . . . . . . . 3  
8
Customizing Your Phone . . . . . . . . . . . . 33  
Silencing all sounds . . . . . . . . . . . . . . . . . . . . . 34  
Choosing ringers . . . . . . . . . . . . . . . . . . . . . . . 34  
Setting sounds for your phone . . . . . . . . . . . . . 35  
Adjusting volume . . . . . . . . . . . . . . . . . . . . . . . 35  
Setting message alerts. . . . . . . . . . . . . . . . . . . . 36  
Using shortcuts. . . . . . . . . . . . . . . . . . . . . . . . . 36  
Personalizing the screen. . . . . . . . . . . . . . . . . . 37  
Creating a secure environment . . . . . . . . . . . . . 39  
Network settings . . . . . . . . . . . . . . . . . . . . . . . . 40  
Data Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . 41  
Setting position location . . . . . . . . . . . . . . . . . . 42  
2
Making and Answering Calls . . . . . . . . . . 8  
Making a call . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Using the speakerphone . . . . . . . . . . . . . . . . . . . 9  
Speed dialing . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Setting up voicemail . . . . . . . . . . . . . . . . . . . . . 11  
Silencing an incoming call . . . . . . . . . . . . . . . . 12  
Calling emergency services . . . . . . . . . . . . . . . . 12  
Setting roaming alerts and ringers . . . . . . . . . . 13  
Controlling network roaming . . . . . . . . . . . . . . 14  
9
Using Media Gallery . . . . . . . . . . . . . . . . 43  
Accessing files . . . . . . . . . . . . . . . . . . . . . . . . . 43  
Creating free space . . . . . . . . . . . . . . . . . . . . . . 44  
3
4
Storing Contacts . . . . . . . . . . . . . . . . . . . 15  
Creating a new contact . . . . . . . . . . . . . . . . . . . 15  
Editing or erasing a contact. . . . . . . . . . . . . . . . 15  
Editing a phone number . . . . . . . . . . . . . . . . . . 16  
Finding contact information . . . . . . . . . . . . . . . 16  
10 Tools & Games. . . . . . . . . . . . . . . . . . . . . 45  
Voice Memo . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
Scheduler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
Alarm Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . 46  
Tip Calculator. . . . . . . . . . . . . . . . . . . . . . . . . . 46  
Calculator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46  
Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Stopwatch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
World Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Flashlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48  
Games . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48  
Brick Attack . . . . . . . . . . . . . . . . . . . . . . . . . . . 48  
Race 21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49  
Using the Camera . . . . . . . . . . . . . . . . . . 18  
Taking a picture . . . . . . . . . . . . . . . . . . . . . . . . 20  
Camera key map . . . . . . . . . . . . . . . . . . . . . . . . 20  
5
6
Entering Text, Numbers,  
and Symbols . . . . . . . . . . . . . . . . . . . . . . 21  
Sending and Receiving  
Text Messages . . . . . . . . . . . . . . . . . . . . . 24  
Sending text messages. . . . . . . . . . . . . . . . . . . . 24  
Retrieving text messages . . . . . . . . . . . . . . . . . . 26  
Customizing message settings . . . . . . . . . . . . . . 28  
11 Connecting to the Internet . . . . . . . . . . . 51  
Using the Web Browser. . . . . . . . . . . . . . . . . . . 51  
7
Using Voice Recognition . . . . . . . . . . . . 30  
Setting up voice dialing . . . . . . . . . . . . . . . . . . . 30  
Calling using voice tags . . . . . . . . . . . . . . . . . . . 30  
Calling using digit dialing . . . . . . . . . . . . . . . . . 31  
Training voice recognition . . . . . . . . . . . . . . . . 32  
12 Getting Help . . . . . . . . . . . . . . . . . . . . . . . 53  
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55  
vi  
Contents  
 
1
GETTING STARTED  
Installing the battery  
Your phone comes with a removable lithium ion  
(LiIon) battery.  
Charging the battery  
You must have at least a partial charge in the  
battery to make or receive calls. Fully charge the  
battery before using the phone.  
To install the battery:  
To charge the battery,  
connect the AC  
1. Hold the phone with the back facing you.  
2. Toward the bottom of  
the phone there is a  
recess to aid you in  
opening the battery  
door. Use your finger to  
pull the battery door  
away.  
adapter to the jack  
on the bottom of the  
phone, then plug the  
adapter into a wall  
outlet.  
3. Place the battery in the  
phone casing with the  
metal contacts toward  
the bottom of the phone.  
The battery icon in the upper-right corner of the  
screen tells you whether the phone is:  
Charging (the icon is animated)  
Partially charged  
4. Place the battery door  
tab in the opening near  
the top of the phone.  
Fully charged  
Recharging the battery  
5. Press the battery door  
until it clicks into  
place.  
You can safely recharge the battery at any time,  
even if it has a partial charge.  
User Guide for the Kyocera Candid KX16 Phone  
1
 
Caring for the battery  
General safety guidelines  
Do not take apart, puncture, or short-circuit  
the battery.  
If you have not used the battery for more than  
a month, recharge it before using your phone.  
Avoid exposing the battery to extreme  
temperatures, direct sunlight, or high  
humidity.  
Never dispose of any battery in or near a fire –  
it could explode.  
Common causes of battery drain  
Playing games or using the Web.  
Keeping backlighting on.  
Taking and viewing pictures.  
Operating in analog ( ) mode. Your phone  
switches between modes to find the best  
signal. To set your phone to operate in a single  
mode, select Menu Settings →  
Network Digital/Analog.  
Operating in digital mode when far away from  
a base station or cell site.  
Using data cables or accessories.  
Operating when no service is available, or  
service is available intermittently.  
High earpiece and ringer volume settings.  
Repeating sound, vibration or lighted alerts.  
2
Getting Started  
 
Getting to know your phone  
Home screen.  
1
2
3
4
5
6
7
8
Left softkey accesses menus and functions.  
Send/Talk key starts or answers calls.  
Speakerphone key activates the speakerphone.  
Keypad for entering numbers, letters, or symbols.  
* Shift key changes the text mode in text entry.  
Jacks for AC adapter (included)*.  
Navigation key positions cursor during text entry. Scrolls through  
list.  
OK key selects a menu item or option.  
9
Right softkey to access Contacts and other menu options.  
End/Power key turns the phone on and off. Ends a call.  
10  
11  
12  
Back key erases characters in text entry. Returns to previous  
screen. Activates the flashlight when pressed and held.  
# Space key enters a space during text entry. Activates Silent mode.  
13  
14  
0 Next key cycles through word choices during text entry.  
User Guide for the Kyocera Candid KX16 Phone  
3
 
Antenna (does not extend).  
Volume key to raise or lower speaker volume.  
Camera key.  
15  
16  
17  
18  
19  
20  
21  
Camera lens.  
Mirror when taking your own picture.  
Camera flash and flashlight.  
External screen displays time, caller ID, signal and  
battery strength.  
Jack for hands-free headset and data cable (sold separately)*.  
22  
*Warning: Inserting an accessory into the incorrect jack will damage  
the phone.  
4
Getting Started  
 
Using Menus  
The contents of the main menu are as follows:  
Recent Calls  
All Calls  
Incoming Calls  
Outgoing Calls  
Missed Calls  
Erase Call Lists  
All Calls Timer  
Home Calls Timer  
Roam Calls Timer  
Contacts  
View All  
Add New  
Find Name  
Speed Dial List  
Voice Dial List  
Messaging Groups  
Camera  
Tools & Games Web Browser  
Brick Attack®  
Race 21TM  
Contacts cont.  
Business List  
Personal List  
Information  
Messages  
New Text Msg  
New Pix Msg*  
Voicemail  
InBox  
Browser Alerts*  
Sent  
OutBox*  
Saved  
Drafts  
Msg Settings  
Group Lists*  
Erase Messages  
Connects to Internet  
Phone Info  
Launches the  
Camera  
Media Gallery  
DoodlerTM  
Voice Memo  
Scheduler  
Alarm Clock  
Tip Calculator  
Calculator  
Timer  
Phone number  
Camera Pictures  
Software Version  
PRL Version  
Factory Config  
ESN  
Technology  
SID  
Images  
Sounds  
Settings  
Silent Mode  
Sounds  
Display  
Stopwatch  
World Clock  
Flashlight  
Icon Key  
Convenience  
Voice Features  
Messaging  
Security  
Network  
Accessories  
BREW Apps  
Launches BREW  
*Not available on all phones, check with your service provider.  
Press  
Press  
Press  
to select Menu.  
In this guide, an arrow tells you to select an  
option from a menu. For example, Menu →  
Settings means select Menu, then select the  
Settings option.  
to select Contacts.  
left, right, up, or down to view  
menus and options*.  
* To change the way the menus appear, select  
Menu SettingsDisplayMainMenuView,  
then select Graphic, List, or Wheel and press  
. See “Choosing a menu view” on page 37 for  
details.  
Press  
Press  
Press  
to select a menu item.  
to back up a menu level.  
to return to the home screen.  
User Guide for the Kyocera Candid KX16 Phone  
5
 
Performing basic functions  
To...  
From the home screen...  
Turn the phone on  
Turn the phone off  
Make a call  
Press  
Press and hold  
Enter the number, and press  
and wait until the phone chimes.  
until the phone beeps.  
.
End a call  
Press  
Press  
.
Answer a call  
.
Access voicemail  
Verify your phone number  
Press and hold  
and follow the system prompts.  
Select Menu Phone Info.  
Silence the ringer on an  
incoming call  
Press , then  
-or-  
to answer.  
Press  
up or down, then  
to answer.  
Activate voice dialing  
Launch the browser  
Record a voice memo  
Access recent calls list  
Launch the camera  
Press  
once and follow the prompts (see page 30).  
Press and hold  
Press and hold  
left.  
right.  
Press  
down.  
Press camera key  
.
6
Getting Started  
 
High-speed (3G) data service is  
available and active on your phone.  
Check with your service provider for  
availability.  
(blinking) The phone is sending high-  
speed data.  
(blinking) The phone is receiving high-  
speed data.  
High-speed data service is available, but  
the phone is dormant.  
Understanding screen icons  
These icons may appear on your phone’s home  
screen and the external LCD.  
The phone is operating in IS2000 (1X)  
digital mode.  
The phone is operating in  
IS95 digital mode.  
The phone is operating in Analog  
(FM) mode.  
The phone is receiving a signal. You can  
make and receive calls. Fewer bars  
indicate a weaker signal.  
The phone is at the home screen. To  
access Menu, press  
The phone is at the home screen. To  
access Contacts, press  
.
.
A call is in progress.  
The phone is set to light up instead of  
ring.  
The phone is set to vibrate or to vibrate  
and then ring.  
Position location is set to your service  
provider and to emergency services.  
Position location is set to emergency  
services only.  
The phone is not receiving a signal. You  
cannot make or receive calls.  
The phone is roaming outside of its  
home service area.  
You have a voice message.  
The phone is in camera mode.  
Camera flash mode is ready.  
Camera timer mode is ready.  
The battery is fully charged. The more  
black bars, the greater the charge.  
The alarm clock is set.  
The phone is in privacy mode or is  
accessing a secure Web site.  
User Guide for the Kyocera Candid KX16 Phone  
7
 
2
MAKING AND ANSWERING CALLS  
Making a call  
Make sure you are in an area where a signal can be  
Answering calls  
When a call comes in and the flip is closed, the  
phone rings and the phone number of the caller  
appears on the external screen. If the number is  
stored in your Contacts directory, the contact  
name also appears.  
received. Look for  
on the home screen.  
Note: The more bars you see in this symbol, the  
stronger the signal. If there are no bars, move to  
where the signal strength is better.  
1. Open the flip and enter the phone number.  
When a call comes in and the flip is open, the  
phone rings and an animated phone icon appears  
on then screen. The phone number of the caller  
also appears if it is not restricted. If the number is  
stored in your Contacts directory, the contact  
name appears.  
2. Press  
.
3. Press  
to end the call or close the flip.  
Redialing a number  
To redial the last number called, received, or  
To answer the call:  
missed, press  
three times. If you see or hear  
Open the flip.  
a message prompting you to speak a name, press  
two more times.  
Press  
-or-  
to answer the incoming call  
Calling a saved number  
If you have already saved a phone number, you  
can use the Contacts list to find it quickly.  
Press  
to answer the incoming call and  
turn on the speakerphone.  
To silence or ignore the call  
1. Press  
to select Contacts.  
When an incoming call is received, you can  
choose to do one of the following:  
2. Scroll down the list to find the contact you  
want to call.  
If the flip is closed, press  
silence the ringer.  
down to  
3. Highlight the name and press  
to dial  
the number.  
If the flip is open, to silence an incoming call,  
press . Then press to answer the call.  
8
Making and Answering Calls  
 
If the flip is open, select Options and then  
Ignore Call to immediately send the caller to  
voicemail. Missed Call appears on your screen  
until the caller leaves a message.  
Turn on the speakerphone  
You may turn on the speakerphone only when the  
flip is open.  
During an incoming call alert, press  
to answer the call and turn on the  
speakerphone simultaneously.  
Note: In the absence of voicemail, this feature  
drops the call.  
Once the speakerphone is turned on,  
Answering calls using the flip  
Speaker is ON” displays on the screen.  
You can set the phone to answer immediately  
when you open the flip. This feature does not  
apply to incoming data/fax calls.  
Turn off the speakerphone  
Press  
to turn off the speakerphone. The  
Speaker is OFF” appears.  
1. Select Menu Settings Convenience →  
Open to Answer.  
message “  
Dealing with missed calls  
2. Select Enabled to set the phone to answer  
when you open the flip.  
When you have missed a call, “Missed Call”  
appears on your screen unless the caller  
leaves a voicemail.  
Select Disabled to have the phone continue  
ringing when you open the flip.  
To clear the screen, open the flip and press  
Adjusting the volume during a call  
to select OK.  
To adjust the earpiece volume during a call,  
press up or down.  
To view details of the call, press  
Calls. Highlight the missed call number and  
press to select Details.  
To return the call, highlight Missed Calls, then  
press  
to select  
Using the speakerphone  
Your Kyocera Candid KX16 phone has a built-in  
speakerphone that you can use during a call when  
the flip is open. This function works only for the  
current call. Once the call is ended, the  
speakerphone turns off and earpiece volume  
returns to normal.  
.
User Guide for the Kyocera Candid KX16 Phone  
9
 
4. Press  
to select Options.  
Setting missed call alerts  
You can set an alert to beep every five minutes  
after you have missed a call.  
Save adds the phone number to the  
Contacts list.  
Send Msg allows you to send a picture  
message to the phone number.  
1. Select Menu Settings Sounds →  
Alerts Missed Call Alert.  
Erase allows you to erase the call record  
2. Press  
to select an option:  
from the list.  
Vibrate, Beep, Freeway, Game, Bloop,  
Winner, Zilofon sets the phone to alert you  
once when a new message is received.  
Note: If the phone number has been classified as  
“secret,” you must enter your four-digit lock code  
to view or edit it. For information on the lock  
code, see “Changing your lock code” on page 39.  
To classify a phone number as secret, see  
“Creating a new contact” on page 15.  
Vibrate & Remind, Beep & Remind, Fwy &  
Remind, Game & Remind, Bloop & Remind,  
Winner & Remind, Zilofon & Remind sets the  
phone to notify you once when a new  
message is received and then notify you  
again every five minutes. To stop a reminder  
Calling recent calls  
alert, press  
Disabled—Turn off message alerts.  
to select Ignore.  
1. Press  
2. Highlight the number you want to call.  
3. Press  
down.  
.
Viewing recent call details  
Details on the last 60 calls you made, received, or  
missed are stored in the Recent Calls list and are  
identified by the following icons:  
Erasing recent calls  
1. Select Menu Recent Calls Erase Call  
Lists.  
Outgoing call  
Incoming call  
2. Select an option: All Calls, Incoming Calls,  
Outgoing Calls, or Missed Calls.  
Missed call (flashing)  
3. Press  
to select Yes.  
Viewing recent calls  
1. Select Menu Recent Calls.  
2. Select a list: All Calls, Incoming Calls,  
Outgoing Calls, or Missed Calls.  
3. Select a recent call item.  
10  
Making and Answering Calls  
 
Using 1-Touch dialing  
Speed dialing  
To call a contact that has a speed dial location:  
Speed dialing allows you to quickly dial a stored  
phone number by entering a one- or two-digit  
speed dialing location number and pressing  
From the home screen, press and hold the  
speed dialing number. If it is a two-digit  
number, press the first digit briefly, then press  
and hold the second digit. For example, if the  
speed dialing location is 15, press  
.
Note: Before you can use speed dialing, you must  
save a phone number as a contact and assign a  
speed dial location to it. Refer to “Creating a new  
contact” on page 15 to create a new contact, or  
“Editing or erasing a contact” on page 15 to add  
speed dial to an existing contact.  
briefly, then press and hold  
.
Setting up voicemail  
Before your phone can receive voicemail  
messages, you must set up a password and record  
a personal greeting with your service provider.  
When you have set up your voicemail, all  
unanswered calls to your phone are automatically  
transferred to voicemail, even if your phone is in  
use or turned off.  
Using speed dialing  
To call a contact that has a speed dial location:  
From the home screen, enter the one- or two-  
digit speed dialing location and press  
.
1-Touch dialing  
1-Touch dialing is the fastest way to speed dial a  
contact that has a speed dial location.  
1. From the home screen, press and hold  
2. Press at the message.  
.
3. Follow the system prompts to create a  
Note: You must (1) enable 1-Touch dialing on  
your phone and (2) have a speed dial location  
assigned to a contact. See “1-Touch dialing” on  
this page.  
password and record a greeting.  
Note: If you are having trouble accessing your  
voicemail, contact your service provider.  
Enabling 1-Touch dialing  
1. Select Menu Settings Convenience →  
1-Touch Dialing Enabled.  
Checking voicemail messages  
When a voice message is received, your screen  
displays “New Messages” along with the  
symbol at the top of your screen. The symbol  
flashes if the message is urgent.  
2. Press  
.
User Guide for the Kyocera Candid KX16 Phone  
11  
 
You can call the code even if your phone is locked  
or your account is restricted. When you call, your  
phone enters Emergency mode. This enables the  
emergency service exclusive access to your phone  
to call you back, if necessary. To make or receive  
regular calls after dialing the code, you must exit  
this mode.  
If you see “New Messages” with the  
flip open  
1. Press  
to select Call, which initiates a call  
to your voicemail number.  
2. Follow the prompts to retrieve the message.  
To clear the screen without checking messages:  
Press  
to select Ignore.  
To exit Emergency mode  
If you see only the  
symbol  
When you have completed the emergency call:  
1. Press and hold  
to initiate a call to your  
1. Press  
to select Exit.  
voicemail number.  
2. Press  
again to confirm your choice.  
2. Follow the prompts to retrieve the message.  
Note: To determine who has access to your  
location, see “Setting position location” on  
page 42.  
You can set the phone to beep or vibrate every  
five minutes to remind you that you have  
voicemail. See “Setting message alerts” on  
page 36.  
Tracking calls  
You can track the number and duration of calls  
made and received on your phone.  
Silencing an incoming call  
To silence an incoming call quickly, press  
. Then press to answer the call.  
1. Select Menu Recent Calls.  
This action silences the current call only. The next  
call will ring as normal.  
2. Select a timer:  
All Calls Timer—Tracks all calls you have  
made and received. This timer cannot  
be reset.  
Calling emergency services  
Note: Regardless of your 3-digit emergency code  
(911, 111, 999, 000, etc.), your phone operates  
as described below.  
Home Calls Timer—Tracks all home calls  
you have made since you last reset  
this timer.  
Dial your 3-digit emergency code and  
press  
Roam Calls Timer—Tracks all roaming  
calls you have made since you last reset  
this timer..  
.
12  
Making and Answering Calls  
 
On any change alerts you with three  
increasing tones if there is a change in  
roaming service or three decreasing tones  
if the phone loses service.  
Timing your calls  
You can set your phone to beep 10 seconds  
before each minute passes when you are on a call.  
Select Menu Settings Sounds →  
Minute Alert Enabled.  
Setting the roam ringer  
You can set a ringer to indicate when an incoming  
call will be subject to roaming charges.  
Receiving data or faxes  
1. Select Menu Settings Sounds →  
Your phone may be able to receive certain data or  
faxes, depending on the system sending the  
information. For more information, see page 41.  
Roam Ringer.  
2. Highlight Enabled to hear the ringer.  
3. Press  
to set.  
Setting roaming alerts  
and ringers  
Setting Call Guard to avoid  
roaming calls  
You can set the phone to warn you before you  
answer or place a call while roaming.  
Setting an alert for roaming  
You may use this setting if you want the phone to  
alert you when you roam outside of your home  
service area.  
Select Menu Settings Convenience →  
Call Guard Call prompt.  
The phone now emits a distinctive roam  
ring to indicate when you are roaming  
during calls.  
1. Select Menu Settings Network →  
Roam/Svc Alert.  
2. Select an option and press  
.
To accept or place a call while roaming,  
When no svc alerts you with three tones  
you must press  
.
decreasing in pitch when service is lost  
and three tones increasing in pitch when  
service is acquired again.  
Note: This functionality is disabled when the  
phone is in emergency mode.  
On roam change alerts you with two  
decreasing tones when roaming service is  
acquired and three increasing tones when  
home area service is acquired again.  
User Guide for the Kyocera Candid KX16 Phone  
13  
 
No roaming prevents you from making  
or receiving calls outside of your home  
service area.  
Controlling network roaming  
Specifying digital or analog mode  
Depending on services available from your service  
provider, you may set the phone to either digital  
or analog mode. This is useful if you are in an  
area that borders on digital service and the  
automatic feature is causing the phone to keep  
switching between modes.  
Note: If your phone has more than one setting for  
Automatic, contact you service provider to  
determine which one to use.  
1. Select Menu Settings Network →  
Digital/Analog.  
2. Select an option and press  
.
Automatic automatically switches the  
phone between digital and analog.  
Analog only sets the phone to work in  
analog mode only.  
Analog call forces a call into analog mode  
for the duration of the next call.  
Digital only sets the phone to work in  
digital mode only.  
Turning roaming on or off  
This setting allows you to control the phone’s  
roaming feature by specifying which signals the  
phone will accept.  
1. Select Menu Settings Network →  
Roam Option.  
2. Select an option and press  
.
Automatic (recommended setting)  
accepts any system the phone service  
provides.  
14  
Making and Answering Calls  
 
3
STORING CONTACTS  
Use your phone’s Contacts directory to store  
information about a person or company. Your  
phone can hold, on average, about 200  
phone numbers.  
To save now, press  
9. To enter additional phone numbers, email and  
Web addresses, or notes, press down  
to select Save.  
repeatedly. For help switching between  
numbers and letters for email or Web  
addresses, see “Changing modes” on page 22.  
Creating a new contact  
1. From the home screen, enter the phone  
number you want to save, including the  
area code.  
Adding a code or extension  
When you save the phone number of an  
automated service, you may include a pause  
where your phone would stop dialing; for  
example, where you would wait to dial an  
extension.  
Note: To save a contact without entering a  
phone number, select Menu Contacts →  
Add New, select an option, and skip to step 3.  
2. Select Save.  
1. Enter the first portion of the phone number.  
2. Select Options.  
3. Select Save New Contact.  
4. Enter a name for the contact. If you need to  
3. Select a type of pause:  
learn how to enter letters, see page 21.  
Time Pause  
Hard Pause  
5. Select Options to add a symbol or smiley.  
6. Press  
down once to move to the  
4. Enter the remaining numbers.  
number field.  
5. Select Save and follow the prompts.  
7. Select Options to add information to the  
contact’s number.  
Editing or erasing a contact  
To make changes to a contact, take these steps.  
1. Select Menu Contacts.  
Time Pause stops dialing for two seconds,  
then continues to dial.  
Hard Pause stops dialing until you  
select Release.  
2. Select View All or Find Name to find the  
contact you want to edit.  
8. Either save now or add more contact  
information.  
3. Highlight the contact to edit and press  
.
User Guide for the Kyocera Candid KX16 Phone  
15  
 
4. Select Options.  
Primary Number—Make this number the  
first one that shows up when you open  
the contact.  
5. Highlight an option and press  
to select  
it:, Edit Contact or Erase Contact.  
Add Voice Dial—Speak the name of the  
contact person for this number so that you  
can dial it using voice recognition (VR).  
For more information, see page 30.  
Editing a phone number  
1. Select Menu Contacts.  
2. Select View All or Find Name to find the  
Erase Voice Dial—Erase the voice dial  
name associated with the number.  
contact you want to edit.  
3. Highlight the contact to edit and press  
.
Edit Voice Dial—Record a new voice  
dial name.  
4. Press  
number you want to edit.  
5. Select Options.  
6. Highlight an option for the phone number and  
press  
down to highlight the phone  
7. Enter the new information and follow  
the prompts.  
8. Select Save, if necessary.  
:
Send Text Msg—Send a text message to  
the phone number you selected.  
Finding contact information  
To find a phone number or contact, you can (1)  
check the frequent contacts list, (2) search the  
Contacts directory, or (3) use Fast Find.  
Add Speed Dial—Assign or remove the  
location you use to speed dial the number.  
View Number—See the phone number  
you selected.  
Checking the Frequent List  
From the home screen, select Contacts. The last  
15 of your most frequently called contacts appear  
when the Frequent List is enabled. Scroll past the  
double line for an alphabetical list of all contacts.  
Erase Number—Erase the number from  
the contact.  
Edit Number—Change the phone number.  
Secret—Make the number secret so that  
it will not appear on the screen until the  
lock code is entered. Secret numbers can  
be called without a lock code. (For more  
information, see “Restricting calls” on  
page 40.)  
To enable the Frequent List setting  
Select Menu Settings Convenience →  
Frequent List Enabled.  
16  
Storing Contacts  
 
Using Fast Find  
Searching the Contacts directory  
1. From the home screen, press the keys  
corresponding to the letters of the name you  
want to find. A matching contact or speed dial  
1. Select Contacts for a list of all contacts.  
To quickly get down the list, enter the first  
letter of the contact. The menu skips to that  
letter of the alphabet.  
entry appears. Press  
down to scroll  
through matching entries.  
-or-  
2. Highlight the name you want, then press  
2. Select Menu Contacts.  
3. Select a search method:  
to call the number.  
View All—List all saved contacts.  
Find Name—Locate a specific name.  
Enter part of the contact name, then select  
Find.  
Speed Dial List, Voice Dial List, Messaging  
Groups, Business List, or Personal List—  
Select a contact from a list.  
4. Scroll down until you find the name you want,  
then press  
.
To call the contact, highlight the number  
and press  
.
To display contact information, press  
.
Setting Fast Find  
With Fast Find, you press one or two keys to view  
close matches of the number you are looking for.  
From the home screen,  
select Menu Settings Convenience →  
Fast Find Enabled.  
User Guide for the Kyocera Candid KX16 Phone  
17  
 
4
USING THE CAMERA  
5. Scroll down to highlight an option and press  
Tips before operating  
your camera  
:
Flash On, Off, or Automatic.  
You cannot activate the camera while on an  
active call or while browsing files in the  
media gallery.  
Resolution options are 640 x 480, 320 x  
240 (best for sending to email and  
viewing), and 160 x 120.  
Once the camera is active, the home screen  
acts as the viewfinder.  
Low Light Mode brightens the picture for  
low light environments.  
If you get a “Low memory” error on your  
phone’s screen, check your resolution and  
quality compression settings. See “Setting up  
the camera” on this page.  
Self Timer options are Off (default) or 3,  
5, or 10 second pauses. When set, the  
camera beeps tones from 3 , 5 or 10  
seconds down to the time the shutter  
snaps the picture automatically. Self Timer  
is not available when Multishot mode  
is activated.  
If there is no activity within approximately  
45 seconds after you turn your camera on,  
then the camera quits and returns to the  
previous launch point.  
Multishot options are On or Off (default).  
When set to On, the camera allows you to  
take multiple pictures (up to six) while  
the camera key is pressed and held. A tone  
will play each time a picture is taken. A  
second tone will play when the final  
picture is taken.  
Menu settings and options can only be  
accessed when the camera is active.  
Setting up the camera  
for photos  
1. With the flip open, select Menu Camera.  
- or -  
Shutter Sound sets the sound used when  
Press the camera key  
.
the shutter closes while taking a picture.  
2. Select Options.  
3. Scroll left or right on the horizontal menu  
bar using  
.
4. Select Settings.  
18  
Using the Camera  
 
White Balance allows the camera to adjust  
to whites. Useful feature for optimizing  
picture taking in different light situations.  
Options are Automatic, Fluorescent,  
Incandescent, or Daylight.  
Menu options for camera mode  
1. Select Menu Camera.  
- or -  
Press the camera key  
.
2. Select Options.  
Color Tone allows the selection of Low  
tone, Medium or High.  
3. Scroll up or down on the horizontal menu bar  
using to scroll through the options:  
Quality sets the picture compression. The  
higher the compression, the better the  
detail of the picture (higher pixel rate).  
Options are Low, Medium, or High  
(default). When set to High, the picture  
file size is larger, using more memory.  
Settings displays available camera settings you  
may set up prior to taking a picture.  
Brightness allows you to adjust the brightness  
of the image in the home screen LCD.  
Camera Pictures displays all pictures taken  
and stored.  
LED flashes a light to indicate a picture  
has been taken. Options are On (default)  
and Off.  
Last Picture shows the most recent  
picture taken.  
Frames allows you to add a frame or a stamp  
to your picture. A frame or stamp cannot be  
removed once it has been used in a picture.  
Restoring camera menu settings  
The following settings revert to the default setting  
each time you enter and exit the camera  
application:  
Zoom, Brightness, Contrast, Camera, MultiShot,  
Color tone, Frames, Self Timer, and Picture Layout.  
The following settings remain at the setting  
you selected each time you enter and exit the  
camera application:  
White Balance, Flash, Resolution, Quality, Shutter  
Sound, and LED.  
User Guide for the Kyocera Candid KX16 Phone  
19  
 
Tip: Press  
zoom out.  
up or down to zoom in or  
Camera mode indicators  
and icons  
The camera mode displays the following onscreen  
indicators and icons:  
3. Take the picture by pressing  
.
The image is immediately saved to  
Media Gallery.  
Icon  
Description  
4. Press  
to select OK.  
- or -  
Press  
Flash on  
to Erasethe picture.  
Top right hand  
corner  
numbers.  
Number of snapshots  
remaining  
5. Press  
to return to the viewfinder and  
take more pictures.  
Zoom level  
6. Press  
when finished taking pictures.  
Bottom left  
hand numbers  
Resolution setting  
Multishot  
Camera key map  
Flip open  
Key  
Camera  
Launch the  
camera  
Menu Screen  
Dismiss menu  
options  
Self Timer (when camera/  
capture key is pressed, the  
icon switches to a number  
and begins counting down)  
In  
Select Capture to Select OK.  
take picture  
Select Options  
Cancel,  
dismisses menu  
Scroll menu  
options right  
Scrolls menu  
options left  
Select menu  
option  
Taking a picture  
Up  
Down  
Zoom in  
Flip open  
Zoom out  
1. Select Menu Camera.  
- or -  
Takes picture  
Press the camera key  
.
2. Focus on the image using the phone’s display  
as a viewfinder.  
20  
Using the Camera  
 
5
ENTERING TEXT, NUMBERS, AND SYMBOLS  
You can enter letters, numbers, and symbols in  
contacts, text messages, and your banner.  
Entering numbers  
To enter a number while in  
a number key once.  
mode, press  
or  
Understanding text entry  
screens  
The current text entry mode (and capitalization  
setting, when applicable) are indicated by icons  
To enter a number while in  
mode, press and hold a number key until the  
number appears on the screen.  
Entering words letter by letter  
characters  
remaining  
capitalization setting  
text entry mode  
Use normal alpha to enter letters.  
1. Press a key once for the first letter, twice for  
the second letter, and so on. If your phone is  
set to Spanish, French, or Portuguese,  
accented letters are available.  
text entry  
fields  
2. Wait for the cursor to move right and enter the  
next letter.  
Text entry modes  
There are five text entry modes:  
Entering words quickly  
When you press a series of keys using  
checks its dictionary of common words and  
guesses at the word you are trying to spell.  
mode,  
Case change  
Numbers only  
Normal alpha  
1. For each letter of the word you want, press the  
Rapid Entry  
key once. For example, to enter the word  
Add Symbol  
“any” press:  
2. If the word doesn’t match what you want,  
press to look at other word matches.  
3. When you see the word you want, press  
.
Note: The mode you start in depends on the task  
you are doing. For example, when entering a  
phone number, you’re in number mode. When  
entering a name for a contact, you’re in normal  
text mode.  
.
User Guide for the Kyocera Candid KX16 Phone  
21  
 
Entering symbols  
While entering text, you can enter symbols by  
pressing  
until you see the symbol you want.  
Using this method, you have access to the  
following symbols:  
.
& @ ,  
1
:
?
To access the full set of symbols:  
1. Select Options.  
2. Select  
Add Symbol.  
down to view the list of symbols.  
3. Press  
4. Press the number key corresponding to the  
symbol you want.  
Changing modes  
Sometimes you need to change modes. For  
example, to enter numbers in an email address  
while in  
mode, you must change to  
mode, enter the numbers, and then change  
back to  
mode to complete the address.  
To change text entry modes, you can either:  
Press and hold  
until the icon for the  
mode you want appears.  
-or-  
Select Options, then the mode.  
Capitalization settings  
You can change capitalization at any time while  
entering text. Simply press  
to choose upper  
or lower case while in Normal Alpha mode.  
22  
Entering Text, Numbers, and Symbols  
 
Quick reference to text entry  
This table gives general instructions for entering letters, numbers, and symbols.  
To...  
Do this...  
Enter a letter  
Use  
mode and press a key until you see the letter you  
want. For more information, see page 21.  
Use mode and press a key once to enter its number.  
For more options, see page 21.  
Enter a number  
Enter a symbol  
Press  
Press  
Press  
until you find the symbol you want. See page 22.  
Enter a space  
.
Erase a character  
.
Erase all characters  
Press and hold  
.
Move the cursor right or left  
Move the cursor up or down  
Change text entry modes  
Capitalize any letter  
Press  
Press  
right or left.  
up or down.  
Press and hold  
.
In  
In  
mode, press  
mode, press  
. Choose  
. Choose  
or  
.
Lowercase any letter  
Select soft options on the screen  
.
Press the appropriate key,  
.
User Guide for the Kyocera Candid KX16 Phone  
23  
 
6
SENDING AND RECEIVING TEXT MESSAGES  
This chapter describes how to send, receive, and  
erase text messages from your phone. For  
information on voicemail messages, see page 11.  
Enter a space or comma after the first  
number. Then enter another recipient  
manually.  
Note: You can send a message to up to 10  
contacts at once. The messages will be sent  
one at a time, once to each addressee.  
Important: The features and menus described in  
this chapter may vary depending on services  
available in your area. In addition, usage charges  
may apply to each message. For details, check  
with your service provider.  
4. When you are done entering addresses,  
press  
field.  
down once to select the Subject:  
Sending text messages  
5. Enter a subject. To learn how to enter text,  
You can only send text messages to phones that  
are capable of receiving them, or to email  
addresses.  
see page 21.  
6. When you are done entering a subject,  
press  
down once to select the Text: field.  
7. Enter the message.  
Creating a text message  
8. To add smileys, select Options Add Smiley.  
1. Select Menu Messages New Text Msg.  
2. Manually enter the recipient’s phone number  
or email address in the Address: field. (To  
learn how to enter text, see page 21.)  
- or -  
Setting sending options  
When you are ready to send a message, you have  
several options for how and when you want the  
message to be received.  
Press  
to select Options. Then select  
1. Once you have completed the message and  
Recent List, Contacts, or Group Lists. For  
more about group lists, see page 28.  
with the Text: field highlighted, press  
select Options.  
to  
3. To add another recipient to this message,  
2. Scroll down to select:  
choose a method:  
Add Address—Return to the “To” screen  
to add another recipient without losing the  
message text.  
Press  
to select Options. Then select  
Recent List, Contacts, or Group Lists.  
- or -  
24  
Sending and Receiving Text Messages  
 
Save Message—Save the message without  
sending.  
When you start a message, the maximum  
character limit (“169” in the example) appears  
below the text entry field. This number counts  
down as you enter characters, until it reaches 0. If  
you continue to enter text after this counter  
reaches 0, a message segment may be appended.  
When you reach the message size limit you are  
prompted to edit the message or alerted that the  
message is being appended.  
Save as Quick Text—Save the message you  
have just entered as a prewritten message,  
then return to the message entry screen so  
you can send the message.  
Settings/ Set Priority—Label the message  
as “Urgent.”  
3. Press  
to select Send.  
Receiving incoming calls while  
creating messages  
If you cannot send messages  
You may not be able to send or receive messages  
if your phone’s memory is nearly full, or if digital  
service is not available at the time. To free up  
memory, erase old messages. See “Erasing  
messages” on page 27.  
If you don’t wish to answer the call, select  
Options Ignore Call. The phone returns to  
the message screen.  
To answer the call, press . Your message is  
saved to the Saved folder. To return to the  
message, select Menu Messages Drafts  
Understanding appended messages  
and press  
to select the message.  
characters  
remaining  
Viewing the OutBox  
You can check the status of messages you have  
sent as long as they have been saved to  
the OutBox.  
text entry  
field  
If you go over the character limit for a single  
message, the phone may automatically append an  
empty segment to your message to make space.  
Important: Your service provider will charge you  
for each message segment.  
User Guide for the Kyocera Candid KX16 Phone  
25  
 
To set the Outbox  
The message has been received by the  
recipient you specified.  
The Outbox default is set to disabled to conserve  
memory. If you want to save your sent messages:  
The message has been received and  
opened by the recipient you specified.  
(This symbol may not be available.  
Check with your service provider.)  
Select Menu Messages Msg Settings →  
Save to Sent.  
Select Enabled to save all sent messages to  
the Outbox.  
The message has been sent to more  
than one recipient.  
Select Prompt to alert you to choose  
whether or not to save your message.  
The message has never been sent, or  
has not been sent since it was last  
modified. You can cancel delivery of the  
message.  
To view the OutBox  
1. Select Menu Messages OutBox.  
2. Press  
up or down through the list of  
messages. One of the following symbols  
appears next to each message:  
Retrieving text messages  
When a text message is received, your screen  
displays “New Messages”, along with the  
symbol at the top of your screen. The symbol  
flashes if the message is urgent.  
The message is pending and will be sent  
when possible. You can cancel delivery  
of the message.  
The scheduled message will be sent at  
the scheduled time. You cannot cancel  
delivery of the message.  
If you see the “New Messages” note  
You can choose to:  
View the messagePress  
.
The message cannot be sent  
because service is not available. An  
alert appears on your phone if the  
message cannot be sent.  
Ignore the messagePress  
.
Note: If you receive a new message while you are  
reading a message, the one you are reading will  
be replaced by the new one. You can find the  
older message in the InBox:  
The scheduled message has been sent  
and will be delivered as scheduled. You  
cannot cancel delivery of the message.  
Select Menu Messages InBox.  
26  
Sending and Receiving Text Messages  
 
Save Object(s), such as sound or pictures,  
from the message. (This option is  
available if the incoming message includes  
a graphic or sound.)  
If you see the  
symbol  
If the  
symbol is flashing, the message is  
urgent.  
1. Select Menu Messages InBox.  
Save Contact to save the sender’s phone  
number or email address in your  
Contacts list.  
A list of all your received messages appears.  
New, unread messages appear in bold.  
indicates an “Urgent” message.  
Save as AutoText to save the text from the  
message as AutoText, which you can insert  
into other messages. Graphics and sound  
will not be saved as part of AutoText.  
2. Press  
up or down to scroll through the  
list of messages.  
3. Press  
to read a message.  
3. Select Done.  
Reading the message  
Note: The  
symbol indicates that a graphic did  
The options available to you may vary. Check with  
your service provider.  
not come through. It may be too large or  
incorrectly formatted.  
Note: Sounds embedded in text messages will not  
play if the phone is set to Silence All mode.  
Setting message alerts  
1. If the text message is long, press  
down to  
You can set your phone to alert you of incoming  
text messages or pages. For more information,  
see “Setting message alerts” on page 36.  
view the entire message.  
2. When you are finished, you can Reply to the  
sender, Play the sound embedded in the  
message, Erase the message, Save the  
message to your Saved folder, or set additional  
Options for the message:  
Erasing messages  
Your phone is designed to store 99 text messages  
and pages. It is a good idea to erase old messages,  
as messages take up memory in your phone.  
View Sender information.  
You have the option of erasing text messages and  
pages as you send or read them, erasing them one  
at a time from the list in the OutBox or InBox, or  
erasing them all at once.  
Forward the message.  
Reply with Copy to reply to the message  
with a copy of the original attached.  
User Guide for the Kyocera Candid KX16 Phone  
27  
 
Erasing single messages  
Erasing messages automatically  
1. Select Menu Messages.  
Use this setting to have old messages  
automatically erased from the InBox when  
memory is low.  
2. Press  
you want to erase: InBox, OutBox, or Saved.  
3. Press  
down to the type of text message  
1. Select Menu Messages Msg Settings →  
Auto-Erase.  
.
4. Highlight the message to erase and press  
2. Highlight Old InBox Msgs and press  
.
.
Older messages will now be erased as new  
messages are received.  
5. Select Options.  
6. Select Erase to erase the message. A  
To disable this setting select Menu →  
Messages Msg Settings Auto-Erase →  
Disabled.  
notification appears: “Erase this message?”  
7. Select Yes to erase the message.  
Note: You can erase a scheduled message from  
the OutBox, but you cannot cancel delivery of  
the message.  
Customizing message settings  
To make messaging easier, you can customize  
settings for sending and receiving messages.  
Erasing all messages  
1. Select Menu Messages Erase Messages.  
Creating group lists  
2. Select a folder to erase all messages from:  
InBox, OutBox, Sent, Saved Folder, or Drafts  
Folder. To erase messages from all folders,  
select All Messages.  
You can create and save a list of multiple  
recipients. Your Candid KX16 phone stores five  
group lists with up to 10 recipients per list.  
1. Select Menu Messages Group Lists →  
3. A message appears: “Erase all messages?”  
Create New.  
Select Yes to erase messages or No to cancel.  
2. Enter a title for the list. For help entering text,  
see page 21.  
3. Press  
to select Next.  
28  
Sending and Receiving Text Messages  
 
4. To enter the first phone number or email  
address, select an option:  
Recent List to select numbers from your  
Recent List.  
New Address to enter the phone number  
or email address manually.  
Contacts List to select numbers from your  
phone book.  
5. Highlight a contact and select Select.  
6. Highlight the contact’s number and select  
Select.  
7. Select Options to select the next number.  
8. Select Recent List or Contacts then the  
contact to add.  
9. When finished, select Done.  
10. To send a message to your new group, see  
“Sending text messages” on page 24.  
User Guide for the Kyocera Candid KX16 Phone  
29  
 
7
USING VOICE RECOGNITION  
Voice recognition allows you to make and  
answer calls by speaking commands into the  
phone’s microphone.  
Editing a voice tag  
1. Select Menu Contacts Voice Dial List.  
2. Highlight the contact you want to edit, and  
Note: You cannot use voice recognition to end a  
press  
to select it.  
call; you must press  
when the flip is open.  
3. Highlight the phone number, select Options.  
4. Select Add Voice Dial, Erase Voice Dial, or  
Setting up voice dialing  
To make or receive calls using voice dialing,  
contacts must be saved with associated voice tags.  
Edit Voice Dial.  
5. Follow the prompts.  
Calling using voice tags  
1. If you haven’t already done so, record a voice  
Creating a voice tag for a contact  
1. Select Menu Contacts View All.  
2. Highlight a contact to add a voice tag to and  
tag for the person you wish to call.  
2. From the home screen, press  
. The phone  
press  
to select.  
responds: “Say a name.”  
3. Press  
down once to select the contact’s  
3. Say the name of the person you want to call.  
number.  
4. If the name you said matches a contact in the  
Voice Dial List, the phone responds: “Calling  
(Name).” Remain silent to make the call, or  
say No to cancel.  
4. Press  
to select Options.  
5. Select Add Voice Dial.  
6. Follow the voice prompts to record a name for  
the contact.  
Note: If the phone finds multiple voice tags  
that sound like the name you said, you will be  
asked to verify which name you want to call.  
Say Yes when you hear the correct name. Say  
No when you hear an incorrect name.  
Viewing entries with voice tags  
Select Menu Contacts Voice Dial List. A  
list of all contacts with assigned voice  
tags appears.  
5. When you are finished with the call, press  
. You cannot end the call with a voice  
command.  
30  
Using Voice Recognition  
 
Say Verify to cause phone to repeat the set  
of digits that you input.  
Erasing all voice tags  
To erase all voice name dial recordings in  
your phone:  
Say Cancel to exit voice recognizer and  
return to the home screen.  
1. Select Menu Settings Voice Features →  
Speak a digit to enter the next digit. Once  
the phone repeats the digit, you can speak  
the next digit or pause to hear the prompt.  
Erase Voice Dial.  
2. Select Yes.  
Calling using digit dialing  
When using digit dialing, you speak digits to dial a  
phone number.  
Using voice features with  
accessories  
You can use voice commands to make a phone  
call or to answer the phone only if your phone is  
connected to an accessory such as a hands-free  
car kit or headset (both sold separately).  
Note: You cannot speak a string of digits. You  
must speak one digit at a time and wait for  
the prompt.  
1. From the home screen, press  
. The phone  
Note: The following features apply only to the  
installed hands-free car kit unless noted.  
responds: “Say a name or say Dial.”  
2. Say Dial. The phone responds: “Speak a digit.”  
To shop for these accessories, visit  
800 349-4188 (U.S.A. only) or 858 882-1410.  
3. Speak the first digit of the phone number you  
want to call. Once the phone repeats the digit,  
you can speak the next digit.  
Waking up the phone  
If you pause, the phone prompts you with the  
following five options. After the prompt, speak  
an option.  
If your phone is connected to a professionally  
installed Kyocera hands-free car kit, you can use a  
voice command to activate the phone to make a  
phone call.  
Say Clear to erase the digit last entered.  
The phone responds: “Digit cleared.”  
To clear the entire phone number, say  
“Clear” again. When the phone prompts  
you with “Clear entire phone number?”,  
say “Yes” to clear or “No” to cancel.  
To activate the Voice Wake-up setting:  
Select Menu Settings Voice Features →  
Voice Wake-Up With accessory.  
Say Call to dial the number.  
User Guide for the Kyocera Candid KX16 Phone  
31  
 
To wake up the phone:  
To answer a call:  
1. Say “Wake Up” and listen for a tone.  
2. Say “Wake Up” again until you hear two tones.  
When you receive an incoming call, the phone  
responds: “Incoming call, answer?” or “Incoming  
roam call, answer?” If the caller is recognized as a  
saved contact entry, then the phone says  
If the phone does not recognize your “Wake up”  
command, see “Training voice recognition” on  
page 32.  
“Incoming call from (Name), answer?”  
Say Yes or press any key except  
.
Answering the phone  
Ignoring an incoming call  
You can set the hands-free car kit to either (1)  
answer automatically or (2) answer using a voice  
command.  
To ignore an incoming call, do one of  
the following:  
Say No and press  
to silence the alert.  
Answering automatically  
Remain silent. The voice alert repeats twice  
and the phone rings once, then returns to the  
home screen.  
You can set your phone to answer automatically.  
Select Menu Settings Accessories →  
Auto-Answer After 5 seconds.  
Training voice recognition  
Answering using voice commands  
If your phone is having trouble recognizing your  
voice, you can train it with the commands Yes,  
No, and Wake up.  
If Auto-Answer is turned off, you can use a voice  
command to answer an incoming call using the  
Kyocera hands-free car kit.  
1. Select Menu Settings Voice Features.  
2. Select Voice Training.  
Select Menu Settings Accessories →  
Auto-Answer Disabled.  
3. Read the message and press  
to select OK  
To activate the Voice Answer setting:  
and continue. Cancel returns you to the  
previous screen.  
1. Select Menu Settings Voice Features →  
Voice Answer.  
4. Select Train All or the item you want to train.  
2. Highlight Enabled, then press  
3. Select Menu Settings Silent Mode →  
Normal Sounds, then press  
.
5. Follow the prompts for each word until  
training is complete.  
.
32  
Using Voice Recognition  
 
8
CUSTOMIZING YOUR PHONE  
The contents of the Settings menu are as follows.  
Silent Mode  
Vibrate Only  
Display  
My Banner  
Voice Features  
Add Voice Dial  
Network  
Data/Fax Calls*  
Vibe then Ring  
Lights Only  
Normal Sounds  
Main Menu View  
Color Themes  
Wallpaper  
Screen Saver  
Backlighting  
Auto-Hyphen  
Language  
Time/Date  
Contrast  
Brightness  
Erase Voice Dial  
Voice Training  
Voice Wake-Up  
Voice Answer  
Expert Mode  
Privacy Alert*  
Data Setup  
User Name  
Set Phone Line*  
Roam/Svc Alert  
Roam Option*  
Digital/Analog*  
Location  
Sounds  
Ringer Volume  
Ringer Type  
Business Ringer  
Personal Ringer  
Roam Ringer  
Flip Open  
Flip Closed  
Pwr On/Off Sound  
Key Volume  
Messaging  
Alerts  
Signature  
Edit QuickText  
Callback Number  
Text Msg Receipt  
Save to Sent  
Accessories  
Pwr Backlighting  
Headset Ringing  
Auto-Answer  
Com Port Speed  
TTY Device  
Convenience  
Airplane Mode  
Open to Answer  
Fast Find  
Auto-Erase  
Default Text  
Key Length  
Key Sound  
Alerts  
Smart Sound  
Minute Alert  
Earpiece Volume  
Spkrphone Volume  
Frequent List  
Hold Call  
1-Touch Dialing  
Web Prompt*  
Call Guard  
Voicemail Number  
Security  
Lock Phone  
Limit Calls  
New Lock Code  
Erase Contacts  
Emergency Numbers  
*Not available on all phones. Check with your service provider.  
User Guide for the Kyocera Candid KX16 Phone  
33  
 
Silencing all sounds  
Choosing ringers  
Your phone is set to make sounds when you  
receive calls, press keys, navigate through menus,  
and receive alerts (such as new messages).  
Your Kyocera Candid Candid KX16 phone has  
multiple ringers you can choose to use for  
incoming calls.  
You can silence all sounds and set the phone to  
vibrate or light up when you receive calls  
and alerts.  
1. Select Menu Settings Sounds →  
Ringer Type.  
2. Scroll down the list to hear the different rings.  
3. Press  
to select a ringer from the list.  
Setting the phone to vibrate or  
light up  
Note: Downloaded ringers are added to the end  
of the standard list of ringers.  
1. Select Menu Settings Silent Mode.  
2. Choose an option and press  
:
Assigning business and  
personal ringers  
Vibrate Only—Causes the phone to vibrate  
for the duration of the incoming call or  
other alert. appears.  
You can assign ringers to contacts classified as  
business or personal in your Contacts directory.  
Vibe then Ring—Causes the phone to  
vibrate for the first 10 seconds and then  
ring for the remainder of the incoming  
Note: To classify a contact as Business or  
Personal, see page 15.  
1. Select Menu Settings Sounds.  
call alert.  
appears.  
2. Ηighlight Business Ringer or Personal Ringer  
Lights Only—Causes the phone to light up  
for the duration of the incoming call or  
and press  
.
3. Select a ringer and press  
.
other alert.  
appears.  
Normal Sounds—Causes the phone to  
ring for the incoming call or alert (in  
effect, returns phone to a non-silent  
mode).  
Importing ringers  
You can download additional ringers to your  
phone using the Kyocera Phone Desktop software  
and Ringster, if available (sold separately). To  
purchase this software and other accessories, visit  
3. Press  
to return to the home screen.  
Note: The phone will ring when it is attached to  
an external power source (such as a charger),  
even if all sounds have been silenced.  
34  
Customizing Your Phone  
 
Adjusting the earpiece volume  
Setting sounds for your phone  
To adjust the earpiece volume manually during a  
You can set your phone to sound tones when you  
open and close the flip, and when you turn the  
phone on and off. Sounds will not occur during  
an incoming call, if you are in a call, or if a  
headset or car kit is attached to your phone.  
call, press the  
key up or down  
To set the earpiece volume:  
1. Select Menu Settings Sounds →  
Earpiece Volume.  
2. Press  
right to increase the volume, or left  
Set sound when flip opens  
to decrease the volume.  
1. Select Menu Settings Sounds →  
Flip Open.  
3. Press  
to select Save.  
2. Scroll through the list to hear the sounds.  
Adjusting the ringer volume  
3. Select a sound and press  
to save.  
1. Select Menu Settings Sounds →  
Ringer Volume.  
Set sound when flip closes  
2. Press  
right to increase the volume, or left  
1. Select Menu Settings Sounds →  
Flip Closed.  
to decrease the volume.  
3. Press  
to select Save.  
2. Scroll through the list to hear the sounds.  
3. Select a sound and press  
to save.  
Adjusting speakerphone volume  
1. Select Menu Settings Sounds →  
Set sound when phone powers on or  
off  
Spkrphone Volume.  
2. Press  
right to increase the volume, or left  
1. Select Menu Settings Sounds →  
Pwr On/Off Sound.  
to decrease the volume.  
3. Press  
to select Save.  
2. Select Enabled. To deselect this sound,  
select Disabled.  
Adjusting key tone volume  
You can change the volume of the tones the phone  
makes when you press the keys.  
Adjusting volume  
You can adjust the earpiece, speakerphone, and  
ringer volume as well as key tones.  
1. Select Menu Settings Sounds →  
Key Volume.  
User Guide for the Kyocera Candid KX16 Phone  
35  
 
2. Press  
right to increase the volume, or left  
Using shortcuts  
Your Kyocera Candid KX16 phone comes with  
four shortcuts when in standby mode (flip open).  
to decrease the volume.  
3. Press  
to select Save.  
Setting key length  
Press  
Press  
Press  
Press  
up  
down Access Recent Calls  
left Launch Web browser  
right Record voice memo  
Access your custom menu  
You can change duration of the tones the phone  
makes when you press the keys.  
1. Select Menu Settings Sounds →  
Key Length.  
2. Choose Normal or Long.  
3. Press  
.
Creating a custom menu  
You can create a custom menu that contains your  
favorite features. After you set up your menu,  
Setting message alerts  
You can choose how you want be alerted of  
incoming voicemail, pages, or text messages.  
simply press and hold  
up to access it.  
1. Press and hold  
up to launch  
1. Select Menu Settings Messaging →  
Custom Menu.  
Alerts.  
2. Press  
3. Scroll through the available options.  
4. Press to select or deselect options. You  
may select more than one feature. Items  
appear in alphabetical order in the menu.  
to select Edit.  
2. Select the type of alert: Message Alert, Page  
Alert, or Voicemail Alert.  
3. Press  
to select an option:  
Vibrate, Beep, Freeway, Game, Bloop,  
Winner, Zilofon sets the phone to alert you  
once when a new message is received.  
5. Press  
to select Save.  
Vibrate & Remind, Beep & Remind, Fwy &  
Remind, Game & Remind, Bloop & Remind,  
Winner & Remind, Zilofon & Remind sets  
the phone to notify you once when a new  
message is received and then notify you  
again every five minutes. To stop a reminder  
Updating your custom menu  
1. Press and hold  
up to launch  
Custom Menu.  
2. Press  
3. Press  
4. Press  
to select Edit.  
to select or deselect options.  
alert, press  
to select Ignore.  
to select Save.  
Disabled—Turn off message alerts.  
36  
Customizing Your Phone  
 
2. Press  
to select Edit.  
Creating a shortcut to frequent  
contacts  
3. Press  
to clear the screen.  
4. Enter your new text.  
By default, your phone lists your entire contacts  
list when you select Contacts. You can also set the  
phone to show a list of your most  
5. Press  
to select Save.  
Choosing a menu view  
frequent contacts.  
Two menu views are available:  
1. Select Menu Settings Convenience →  
Frequent List.  
1. Select Menu Settings Display →  
Main Menu View, then the option you want:  
2. Select Enabled to include the list or  
Disabled to remove it.  
Graphic displays graphical icon view of  
menu items.  
Using the Frequent Contacts shortcut  
List displays menu items in text format.  
From the home screen, press  
to select  
Wheel displays a rotating graphic image of  
the menu items.  
Contacts. Your 15 most frequently called  
contacts appear at the top of the list, followed  
by your complete contact list.  
2. Press  
up or down to scroll menu views.  
to return to the home screen. The  
3. Press  
Choosing a different language  
Your phone may display alternative languages.  
next time you select Menu, you will see the  
menu view you selected.  
1. Select Menu Settings Display →  
Adjusting the backlighting  
Language.  
Your screen lights up while you are in a call or  
when you press a key on the keypad. However,  
you can set the length of time that bright  
backlighting remains on.  
2. Select a language, and press  
.
Personalizing the screen  
Changing your banner  
1. Select Menu Settings Display →  
Backlighting Duration.  
The banner is the personal label for your phone.  
It appears on the home screen above the time and  
date. The banner can be up to 14 characters long.  
2. Select an option from the list:  
7 seconds, 15 seconds, or 30 seconds—  
Turn backlighting on for 7, 15,  
1. Select Menu Settings Display →  
or 30 seconds after your last keypress.  
My Banner.  
User Guide for the Kyocera Candid KX16 Phone  
37  
 
7 sec. & in call, 15 sec. & in call, or 30 sec.  
& in call—Turn backlighting on for the  
duration of a call, and for 7, 15, or 30  
seconds after your last keypress.  
Changing the display contrast  
1. SelectMenuSettingsDisplayContrast.  
2. Press  
left or right to adjust the contrast.  
3. Press  
to select Save.  
Note: These settings drain the battery more  
quickly and reduce talk and standby times.  
Setting numbers to auto-hyphenate  
Auto-hyphenation, when enabled, automatically  
inserts hyphens into your phone numbers to be  
consistent with the U.S. dialing plan.  
Using Power Save Mode  
You can conserve battery life by activating Power  
Save mode to dim the backlight set in the  
procedure above. The backlighting appears for  
the selected duration but is less bright than with  
Power Save off.  
For example, 1-222-333-4444.  
Select Menu Settings Display →  
Auto-Hyphen Enabled.  
Select Menu Settings Display →  
Selecting a screen saver  
Backlighting Pwr Save Mode On.  
Screen savers appear on the home screen when  
the flip is open and are activated 10 seconds after  
the last keypress. Incoming calls and alerts  
override screen savers.  
Setting power backlighting  
You can set backlighting to remain on when an  
external power source, such as the AC adapter, is  
used with the phone.  
1. Select Menu Settings Display →  
Screen Saver.  
Note: Power backlighting may not be available  
with the optional desktop charger or other  
accessories.  
2. Highlight a screen saver and press  
. The  
image displays.  
3. Press  
to assign the screen saver.  
1. Select Menu Settings Accessories →  
4. Press  
to return to the home screen and  
Pwr Backlighting.  
wait 10 seconds to view the screen saver you  
chose.  
2. Select Always On to keep backlighting on.  
Note: The battery charges more slowly when  
power backlighting is on.  
Note: Downloaded screen savers are added to  
the end of the list.  
38  
Customizing Your Phone  
 
Selecting wallpaper  
Creating a secure environment  
Wallpaper appears on the home screen.  
This section describes all the features involved in  
securing your phone and preventing access to  
personal information. All security features are  
shielded by a four-digit lock code.  
1. Select Menu Settings Display →  
Wallpaper.  
2. Highlight a wallpaper design and press  
.
3. Press  
to assign the wallpaper.  
Changing your lock code  
4. Press  
to return to the home screen.  
The lock code is typically 0000 or the last 4 digits  
of your phone number.  
Selecting a color theme  
1. Select Menu Settings Security.  
2. Enter your four-digit lock code.  
You can select a color theme for the display  
background of your phone.  
3. Select New Lock Code. A message appears:  
1. Select Menu Settings Display →  
“Change Code?”  
Color Themes.  
4. Press  
digit code.  
to select Yes and enter a new four-  
2. Scroll through the options to view the  
color themes.  
5. Enter your new lock code again.  
3. Highlight a color theme from the list and  
press  
.
Locking your phone  
4. Press  
to return to the home screen.  
When your phone is locked, you can call only  
emergency numbers or your service provider  
number. You can still receive incoming calls.  
Choosing a different time/date format  
1. Select Menu Settings Display →  
Time/Date.  
1. Select Menu Settings Security.  
2. Enter your four-digit lock code.  
3. Select Lock Phone.  
2. Highlight the option you want.  
3. Press  
to save the setting.  
4. Highlight an option:  
Never does not lock the phone.  
On power up locks the phone every time  
you turn it on.  
Now locks the phone immediately.  
5. Press  
.
User Guide for the Kyocera Candid KX16 Phone  
39  
 
2. Enter your four-digit lock code.  
3. Select Limit Calls.  
Unlocking the phone  
1. From the home screen, press  
to  
select Unlock.  
4. Choose an option:  
2. Enter your four-digit lock code.  
No Limit limits no calls.  
Limit Outgoing calls only. Incoming calls  
can still be received and answered.  
Designating emergency numbers  
The emergency numbers feature allows you to  
specify three personal phone numbers that can be  
called when the phone is locked.  
Limit All calls, both incoming and  
outgoing.  
1. Select Menu Settings Security.  
2. Enter your four-digit lock code.  
3. Select Emergency Numbers.  
4. Select an Unassigned slot.  
Erasing all contacts  
You can erase all entries from your  
Contacts directory.  
1. Select Menu Settings Security.  
2. Enter your four-digit lock code.  
3. Select Erase Contacts.  
5. Enter the phone number, including the area  
code. Do not enter 1 before the area code.  
6. Press  
Notes:  
to select Done.  
4. Select Yes to erase all contacts. A message  
appears: “Erase ALL Contacts?”  
You can view these numbers only when they’re  
being entered for the first time.  
5. Press  
to select Yes to erase all contacts.  
Network settings  
You cannot edit these numbers.  
To make a call to an emergency number from  
a locked phone, you must dial the number  
(including area code) exactly as it was stored  
in Emergency Numbers.  
Switching between phone lines  
Your phone can have two service accounts, or  
phone lines, associated with it. Each phone line  
has its own phone number.  
Restricting calls  
When you are using one line, you cannot receive  
calls from the other. It would be as if the phone  
were “off” for that number. Your voicemail,  
however, will still take messages. All contacts and  
settings are shared for both lines.  
You can restrict the calls that can be made from  
your phone to emergency numbers, your  
contacts, and service provider numbers.  
1. Select Menu Settings Security.  
40  
Customizing Your Phone  
 
Note: You must first establish a second phone  
line with your service provider. Once established,  
a second phone number becomes available in the  
menu for selection:  
Note: To purchase a cable call (800) 349-4188  
(U.S.A. only), (858) 882-1410, or visit  
1. Connect the phone to the laptop or PC.  
1. Select Menu Settings Network →  
2. Set the Com speed.  
Set Phone Line.  
3. Select Menu Settings Network →  
2. Select one of the two lines and press  
.
Data/Fax Calls.  
4. Press  
to select an option:  
Data Settings  
Voice only—Allow only voice calls.  
Setting Com port speed  
Fax, next call or Data, next call—Set the  
phone to fax mode or data mode for the  
next incoming call or the next 10 minutes.  
The Com Speed sets the data rate at which your  
phone connects to a laptop or PC.  
Fax, until off or Data, until off—Forces the  
phone into data mode until the phone is  
turned off.  
1. Select Menu Settings Accessories →  
Com Port Speed.  
2. Select the speed. The options are: 19.2 kbps,  
Note: You cannot receive voice calls while the  
115.2 kbps (default), 230.4 kbps and Other.  
phone is in data/fax mode.  
Note: There may be a higher charge for making  
calls using high-speed data in areas where 1X  
service is available. Check with your service  
provider for details.  
Connecting to a TTY/TDD device  
You can connect the phone to a TTY device for the  
hearing impaired. Note: Enable TTY only when  
using the phone with a TTY device.  
Setting the phone to receive data  
or faxes  
1. Connect the TTY device to the phone.  
2. Enter  
your keypad.  
from  
Your phone may be able to receive certain data or  
faxes, depending on the system sending the  
information. You cannot receive voice calls while  
the phone is in data/fax mode. To receive data or  
faxes, you must connect the phone to a laptop or  
PC and switch the phone from voice mode to data/  
fax mode.  
3. Press  
4. Press  
5. Press  
6. Press  
to select the TTY option.  
to clear the message.  
down to highlight TTY On.  
.
User Guide for the Kyocera Candid KX16 Phone  
41  
 
Note: TTY/TDD service may not be available.  
Check with your service provider for more  
information.  
Setting position location  
This setting allows you to share your location  
information with network services other than  
emergency services (911, 111, 999, 000, etc.), in  
markets where service has been implemented.  
Note: This feature works only when your phone is  
in digital mode. You do not have the option of  
turning off the locator to emergency services.  
1. Select Menu Settings Network →  
Location.  
2. At the message prompt, press  
to select  
OK and continue.  
3. Select 911 Only or Location On.  
911 Only (default) shares your position  
information only with emergency services  
when you call your 3-digit emergency  
code (911, 000, 111, etc.).  
Location On shares your position  
information with your service provider’s  
network, in addition to emergency  
services.  
42  
Customizing Your Phone  
 
9
USING MEDIA GALLERY  
The media gallery stores and displays all the  
image and sound files in the phone.  
Modify allows you to change the following:  
Rotate - select 90º right, 180º, 90º left, Flip  
horizontal, and Flip Vertical.  
Resize - select 90%, 75%, 50%, and 30%.  
Accessing files  
1. Select Menu Media Gallery.  
2. Select an option:  
Brightness - press  
Sharpness - press  
Saturation - press  
left or right to adjust.  
left or right to adjust.  
left or right to adjust.  
Camera Pictures displays thumbnails of  
the photos you have taken in  
chronological order.  
Hue - press  
left or right to adjust.  
Auto Adjust - automatically adjusts  
all levels.  
Color Tone - change the picture to  
grayscale, negative, sepia, or emboss.  
Images displays a list of categories that  
contain preloaded, downloaded, saved, or  
created files such as wallpaper, screen  
savers, or caller IDs.  
Zoom allows you to zoom in or out on  
the picture.  
Sounds displays a list of categories that  
contain saved or downloaded sounds such  
as ringers and voice memos.  
Take Picture to snap another photo.  
Lock to prevent accidentally erasing  
the photo.  
Rename the picture.  
Browsing pictures  
1. Select Menu Media Gallery →  
Details of the file.  
Camera Pictures.  
Browsing images  
The images menu allows you to assign your files  
to various applications.  
2. Highlight a picture and press  
to  
select View.  
3. Press  
to select Erase.  
1. Select Menu Media Gallery Images.  
- or -  
2. Use  
to highlight the menu item you want:  
Press  
to select Options:  
Saved Images displays images you have  
Assign picture as a Caller ID or  
saved.  
as wallpaper.  
Wallpapers displays wallpaper selections.  
User Guide for the Kyocera Candid KX16 Phone  
43  
 
Screen Savers displays available  
screensavers.  
Ringers contains ringers saved on your  
phone.  
Caller IDs displays pictures and images  
that can be assigned to saved contacts.  
Voice Memos contains voice memos you  
made to yourself.  
Doodles displays files created with  
3. Select OK to display the files in that menu.  
Doodler.  
4. Select Options. Choose from the following  
3. Select OK to display the files in that menu.  
options:  
4. Highlight an image and select Options.  
Note: Options vary according to menu  
selection.  
Erase the sounds.  
Assign a sound as a ringer.  
Rename a ringer.  
Choose from the following options:  
Details gives you the file size of the sound.  
Erase All erases all sounds stored.  
Send launches the messaging application.  
Erase the image.  
5. Select Close when done.  
Set As Default sets as default setting.  
Assign an image as a caller ID, wallpaper  
Creating free space  
or screen saver.  
If your phone does not have enough memory to  
store a file, a dialog displays and asks you if you  
want to create space.  
Rename an image.  
Details gives you the file size of the image.  
Erase All erases all images stored (images  
Select Yes to display the file browser  
(categories) with the memory needed and  
available memory.  
must not be locked).  
5. Select  
or  
when done.  
Select No to return to the previous screen and  
no files are saved or downloaded.  
Browsing sounds  
The sounds menu allows you to view and listen to  
all sound files stored on the phone.  
The actions are limited to the following:  
Erase the selected file (you cannot erase  
1. Select Menu Media Gallery Sounds.  
locked files).  
2. Use  
to highlight the menu item you want:  
Done re-attempts the download or save.  
Saved Sounds contains sounds saved on  
your phone.  
44  
Using Media Gallery  
 
10 TOOLS & GAMES  
Erasing a saved voice memo  
Voice Memo  
The Voice Memo tool allows you to record and  
play back audio memos.  
1. Select Menu Tools & Games →  
Voice Memo Recorded Memos.  
2. Highlight the memo and select Options.  
Recording a voice memo  
3. Select Erase. The prompt “Erase file?”  
1. Select Menu Tools & Games →  
Voice Memo Record New.  
-or-  
appears.  
4. Select Yes or No.  
Press and hold  
2. Say your memo and press to  
right.  
Scheduler  
The Scheduler allows you to schedule events and  
set reminder alerts.  
select Stop.  
3. Select Save to save your memo.  
Note: If an incoming call is received while you’re  
recording a memo, the memo is saved and the  
incoming call screen displays.  
Creating an event  
1. Select Menu Tools & Games Scheduler.  
2. Press  
down to select Add Event and  
.
Playing or reviewing a memo  
press  
1. Select Menu Tools & Games →  
3. Enter a name for the event. For help entering  
Voice Memo Recorded Memos.  
text, see page 21.  
2. Highlight the memo to review.  
4. Select Next.  
3. Press  
to select Play.  
5. Enter the time, length, and alarm for event.  
Naming a saved voice memo  
Press  
minutes, and timing of alarm.  
Press left or right to move  
between fields.  
up or down to select date, hour,  
1. Select Menu Tools & Games →  
Voice Memo Recorded Memos.  
2. Highlight the memo and select Options.  
3. Select Rename. Enter a name for the memo.  
4. Select Save.  
6. Select Next, enter a note if required.  
7. Select Done.  
5. Press  
to return to the home screen.  
User Guide for the Kyocera Candid KX16 Phone  
45  
 
Viewing, editing, or erasing an event  
Tip Calculator  
The Tip Calculator helps you calculate how much  
tip to include on a bill.  
1. Select Menu Tools & Games Scheduler.  
2. Select View Day or View Month to find the  
event you want to view, edit, or erase.  
1. Select Menu Tools & Games →  
Tip Calculator.  
3. Press  
an event and press  
4. Select Edit or Options. Follow the prompts.  
up, down, left, or right to highlight  
to select it.  
2. Enter the amount of your bill.  
3. Select Next.  
5. Press  
to return to the home screen or  
to return to scheduler options.  
4. Select the amount you want to include as a tip  
(10%, 15%, 18%, 20%, Other) and press  
. Your total bill appears, including tip.  
Alarm Clock  
Use the Alarm Clock to set an alert for a specific  
time. The alert occurs only if the phone is on.  
1. Select Menu Tools &Games Alarm Clock  
2. Select Set.  
5. To split the bill, press  
6. Press to clear the default of 2 guests.  
7. Enter the number of guests and press  
to select Split.  
to  
select Next. The amount each guest pays is  
calculated.  
Press  
and minutes.  
Press  
hours, minutes, and a.m./p.m.  
Use the phone keypad to enter numbers.  
up or down to select an hour  
8. Select Done.  
left or right to switch between  
Calculator  
Use the calculator for basic mathematical  
equations.  
3. Press  
to select Done and save the setting.  
1. Select Menu Tools & Games Calculator.  
4. When the alarm rings, select Off to turn off the  
alarm or Snooze to silence the alarm for  
10 minutes.  
2. Use the keypad to enter numbers.  
3. Use  
to select mathematical operations.  
Navigation:  
Left x (multiply) Up  
Right ÷ (divide) Down - (subtract)  
4. Press to calculate the result.  
+ (add)  
46  
Tools & Games  
 
Example: Enter 5, press  
left to select X, enter  
4. Select Reset to clear the counter.  
5. Press to return to the home screen.  
2, then press  
to obtain the result of 10.  
to return to the home screen.  
to clear the screen.  
5. Press  
World Clock  
World Clock may not be available on your phone.  
Check with your service provider for availability.  
The World Clock lets you check times in cities  
around the world in relation to local time.  
6. Press  
Options  
Adds displayed digit to the value stored  
in memory.  
M+  
Displays currently stored value on  
screen.  
1. SelectMenu Tools&Games WorldClock.  
MR  
MC  
The World Clock menu is displayed. Your  
local time and date is on the first line,  
followed by your selected world city and that  
city’s time and date. When you first access  
World Clock, you are prompted to select a  
city.  
Clears value currently stored in memory.  
Timer  
This timer counts down for a specified amount of  
time. It beeps when that amount of time has  
elapsed.  
2. Press  
to select Cities.  
The Cities menu is displayed, showing 85  
world cities in alphabetical order.  
1. Select Menu Tools & Games Timer.  
2. Select Set.  
3. Press  
up or down to scroll through the  
cities list. You can also use the number keys  
(2-9) to alphabetically tab through the list.  
3. Press  
minutes, and seconds. To move the cursor,  
press left or right.  
up or down to set the hours,  
4. Press  
to select a city, like Athens.  
4. Select Start and begin the countdown.  
Select Stop to pause the countdown.  
Select Reset to clear the timer.  
The World Clock menu is displayed again,  
with Athens’ time and date.  
From the World Clock menu, you can also select  
5. Press  
to silence the alarm.  
Search to search by city or country.  
1. Select Search from the World Clock menu.  
Stopwatch  
1. Select Menu Tools & Games Stopwatch.  
2. Select Start to begin counting.  
The Search By menu is displayed.  
3. Select Stop to stop counting.  
User Guide for the Kyocera Candid KX16 Phone  
47  
 
2. Select your type of search.  
-or-  
Press  
Press  
by Country.  
search by City.  
Select Menu Tools & Games →  
Flashlight Turn On. The flashlight remains  
on for 15 minutes.  
down, then press  
to search  
3. If you search by City, the Find City screen  
To turn the flashlight off, select Menu Tools →  
Flashlight Turn Off.  
- or -  
is displayed.  
a. Use your number keys (2-9) to enter the  
letter(s) by which you want to search. For  
example, press 2 once to enter the letter A.  
Press  
.
b. Press Search.  
Games  
c. Cities beginning with A are displayed, like  
The games in this section may not be available  
on your phone. Check with your service provider  
for availability.  
If you receive an incoming call alert while you are  
playing Brick Attack™ or Race 21™, the game is  
paused and exited. You can return to play once  
the call alert ends. Games do not remain paused if  
the phone is turned off or loses power.  
Anchorage, Athens, and Atlanta.  
d. Use  
press  
to move through the list, then  
to select a city.  
4. If you search by Country, the Find Country  
screen is displayed.  
a. Use your number keys (2-9) to enter the  
letter(s) by which you want to search. For  
example, press 2 once to enter the letter A.  
Brick Attack  
b. Press Search.  
The goal of this game is to eliminate bricks  
arranged in levels. You send a moving ball  
upward using a paddle at the bottom of  
the screen.  
c. Countries beginning with A are displayed,  
like Afghanistan, Algeria, and Australia.  
to move through the list, then press  
to select a country.  
Use  
1. SelectMenu Tools&GamesBrickAttack.  
Flashlight  
2. Press  
to select Yes at the prompt, “Turn  
off backlight to conserve battery?”  
The flashlight is located on the top-right corner of  
your phone. You can turn on the flashlight in  
two ways:  
3. Press  
to select New.  
To pause the game, press  
to Resume.  
, then press  
From the home screen, press and hold  
. The  
flashlight remains on until you release the key.  
48  
Tools & Games  
 
To move the paddle, press  
right.  
left or  
You lose points each time you exceed 21  
in a column.  
To exit the game, highlight Exit and press  
Select Skip to skip one card per round.  
.
5. Press  
to select  
to get your score  
and advance to the next round.  
Race 21  
6. Select an option and press  
to select it.  
New GameInitiates game play. To pause  
the game, press . From here you can  
choose Resume, New or Quit.  
Resume GameReturns you to the game  
This game is a timed variation of Black Jack. Each  
game comprises three 90-second rounds. To  
score points, add cards in each of the four  
columns, trying to reach but not exceed 21 in  
each column within during the course of the  
game.  
you were last playing.  
ScoreboardProvides you with the top  
1. Select Menu Tools & Games Race 21.  
five scores.  
2. Press  
at the splash screen.  
MusicChoose when you hear music  
with this game. Select from Music Always,  
Sound Effects, Instructions, Credits,  
During Title, or No Music.  
3. Select New Game. The first card to be placed  
is shown at the top left of the screen. Press a  
key to add a card to the row as follows:  
Add cards to the first row  
Add cards to the second row  
Add cards to the third row  
Add cards to the fourth row  
7. Press  
to end all games.  
Doodler  
You can create and save graphics on your phone.  
Shortcut: Press  
left or right to choose arrows  
1. Select Menu Tools & Games Doodler.  
at the bottom of the screen. Then press  
add cards to corresponding rows.  
Note: Each time you place a card, a new card  
appears for placement.  
to  
2. Press  
at the splash screen.  
3. Select New Doodle to open the drawing screen  
The cursor is located in the middle of the  
screen.  
4. Select Options to choose the Colors, Tools,  
4. Continue placing cards until you are satisfied  
Lines, or Shape you want to use.  
with your selections.  
You can pause or end the game at any time  
by pressing  
.
User Guide for the Kyocera Candid KX16 Phone  
49  
 
5. Use keys 1–9 or  
to  
Return cursor to center  
Previous screen  
move the cursor around the  
screen as indicated.  
6. When finished, select  
Options Save. The image  
is saved to My Pictures.  
Saving a doodle  
To move cursor away from drawing:  
It is a good idea to save the doodle while you are  
working on it. If you receive a call while creating  
an unsaved doodle, it will be lost.  
1. Select Options Tools.  
2. Select  
, then Done.  
Select Options Save and press  
The image will be saved in Menu →  
Media Gallery Images Doodles.  
.
3. Press a number key to move the cursor.  
To erase part of drawing:  
1. Select Options Tools.  
Resuming a doodle  
2. Select  
, then Done.  
To return to another saved doodle:  
3. Press a number key to move the eraser.  
Select Menu Tools & Games Doodler →  
Resume Doodle.  
To Navigate: Use the following keys to doodle.  
To:  
Use:  
Note: You can also go to Menu Media  
Gallery Images Doodles.  
Select Options  
Clear screen  
Shortcut to Tools  
Draw, erase, or move cursor/  
shape UP  
up  
Draw, erase, or move cursor/  
shape DOWN  
Draw, erase, or move cursor/  
shape LEFT  
down  
left  
Draw, erase, or move cursor/  
shape RIGHT  
right  
50  
Tools & Games  
 
11 CONNECTING TO THE INTERNET  
some Web menu options at the bottom of the  
screen.  
Using the Web Browser  
You can use your phone to browse the Internet if  
you have obtained phone Internet services from  
your service provider and if over-the-air Internet  
access is available in your area.  
A
appears in a secure session.  
An underline and an arrow indicate that  
there is more text. Press down to view  
to return to the  
more text. Press  
previous screen.  
Note: You cannot receive incoming calls while  
you are using the Web Browser.  
To choose a site, highlight it and press  
Starting the Web Browser  
1. Select Menu Web Browser.  
-or-  
to select Go.  
4. When you have finished using the Internet,  
press to exit the browser.  
Press and hold  
left to launch the browser.  
Using the Web menu options  
A message about airtime fees appears every  
time you start the browser.  
The following options may appear on your screen:  
Home returns you to the main Web Browser  
window, or home page.  
To cancel the message, see “Changing the Web  
prompt” on page 52.  
Mark Site saves the current location as a  
bookmark for easy access.  
For more information about how airtime is  
charged, contact your service provider.  
Bookmarks displays a list of your saved  
Web sites.  
2. Press  
to continue.  
If this is the first time you have connected to  
the Internet, a message informs you that  
security is not yet enabled for your  
Web Browser.  
Setup gives you options for changing how  
information is displayed.  
Show URL displays the entire URL.  
About Openwave displays information  
3. Press  
to select Yes to enable security.  
about your Web Browser version.  
When you are connected, a browser home  
page appears. It has a list of bookmarks and  
User Guide for the Kyocera Candid KX16 Phone  
51  
 
Encryption should not be used unless you  
are instructed to do so by your service  
provider.  
Changing the Web prompt  
1. Select Menu Settings Convenience →  
Web Prompt.  
UP.Link selects a different browser server.  
You can use this option if you have more  
than one Web Browser account.  
2. Highlight an option and press  
to select  
it:  
At Start confirms that airtime fees will be  
applied when you use the browser.  
Restart restarts the Web Browser.  
At End verifies you want to exit the  
browser.  
Searching for a Web site  
How you search for a Web site depends on your  
service provider. For more information, contact  
your service provider.  
Both prompts you when you start the  
browser and exit the browser.  
No Prompts does not use any prompts.  
Going to a bookmarked site  
1. Select Menu Web Browser. If you see a  
message prompt, press  
to continue.  
2. From your Web home page, select  
Bookmarks. A list of bookmarks appears.  
3. Enter the number corresponding to the  
bookmark you want and press  
.
Checking Net alerts  
Alerts received from a Web site are sent to your  
Net Alerts inbox.  
1. Select Menu Messages Browser Alerts.  
This action launches the browser inbox.  
2. Press  
to accept browser fees.  
3. Select an alert and follow the prompts.  
52  
Connecting to the Internet  
 
12 GETTING HELP  
Mexico:  
001-866-650-5103  
Customer support  
Your service provider’s customer support  
New Zealand: 0-800-990-100  
department may be accessible directly from your  
phone when you dial a number such as *611  
(check with your service provider). They can  
answer questions about your phone, phone bill,  
call coverage area, and specific features available  
to you, such as call forwarding or voicemail.  
Panama:  
Peru:  
001-800-201-1984  
0-800-51-934  
Puerto Rico:  
Venezuela:  
1-866-664-6443  
0-800-100-2640  
Before requesting support, please try to  
reproduce and isolate the problem. When you  
contact the Customer Care Center, be ready to  
provide the following information:  
For questions about the phone features, refer to  
the materials provided with your phone, or visit  
The name of your service provider.  
For additional questions, you may contact the  
Kyocera Wireless Corp. Customer Care Center in  
any of the following ways:  
The actual error message or problem you are  
experiencing.  
The steps you took to reproduce the problem.  
The phone’s electronic serial number (ESN).  
To locate the ESN select Menu Phone  
Info and scroll down to ESN: for the 11-  
digit number.  
Phone: 1-800-349-4478 (U.S. and Canada)  
or 1-858-882-1401. Customer support  
phone numbers are also available in the  
following countries.  
Argentina:  
Australia:  
Brazil:  
0-800-666-0052  
800-507-000  
0-800-55-2362  
800-43-1212  
Chile:  
Colombia:  
India:  
01-800-700-1546  
Toll free:1-600-121214  
Toll: 0124-284-5000  
User Guide for the Kyocera Candid KX16 Phone  
53  
 
Qualified service  
If the problem with your phone persists, return  
the phone with all accessories and packaging to  
the dealer for qualified service.  
Phone accessories  
To shop for Candid KX16 phone accessories, visit  
call us at (800) 349-4188 (U.S.A. only) or  
(858) 882-1410.  
Become a product evaluator  
To participate in the testing and evaluation of  
Kyocera Wireless Corp. products, including  
cellular or PCS phones, visit beta.kyocera-  
wireless.com.  
54  
Getting Help  
 
INDEX  
Numerics  
1-touch dialing, 11  
hands-free headset  
purchasing, iv, 54  
hard pause, 15  
creating, 36  
updating, 36  
A
D
alarm clock, 7, 46  
alerts  
data/fax setup, 13, 41  
digital mode, 7  
display contrast, 38  
doodler, 49  
I
icons, 7  
inbox, 27  
for messages, 36  
for missed calls, 10  
analog mode, 7  
auto text, 25  
L
language, 37  
lights  
E
emergency  
auto-hyphenation, 38  
lights-only mode, 7, 34  
calls, 12  
B
limiting calls out, 40  
lock code, 39  
locking  
emergency mode, 12  
exit emergency mode, 12  
position location, 7, 42  
erasing  
banner, 37  
battery, 1  
blocking outgoing calls, 40  
Brick Attack, 48  
phone, 39  
contact entries, 40  
text messages, 27  
M
memory, saving, 27  
menu view, 37  
C
calculator, 46  
call counters, 12  
calls  
F
fast find, 17  
fax mode, 41  
finding contact information, 16  
flip  
answering calls, 9  
frequent contacts, 16  
N
number mode, 21  
answering, 8  
O
missed, 9  
outbox, 25  
redialing, 8  
camera  
P
menu options, 19  
sending a picture, 19  
setting up, 20  
taking a picture, 20  
color themes, 39  
com port speed, 41  
contacts directory, 15  
contrast, 38  
phone numbers  
editing, 16  
G
games  
verifying your own, 6  
Brick Attack, 48  
doodler, 49  
race 21, 49  
phone, unlocking, 39  
position location, 7, 42  
R
H
race 21, 49  
recent call icons, 10  
resetting the phone, iv  
hands-free car kit  
answering using voice, 32  
purchasing, iv, 54  
countdown timer, 47  
custom menu  
User Guide for the Kyocera Candid KX16 Phone  
55  
 
V
ringers  
choosing types, 34  
vibrate, 7, 34  
voice answer, 32  
voice dialing, 30  
voice memo  
erasing, 45  
naming, 45  
recording, 45  
voicemail, 11  
setting up, 6  
volume  
for roaming calls, 13  
silencing, 6  
volume, 35  
roaming, 7  
alerts, 13  
controlling, 14  
ringer, 13  
S
saved phone numbers  
editing, 16  
scheduler, 45  
screen contrast, 38  
screen icons, 7, 21, 26, 34  
screen savers, 38  
secret contacts, 10  
security, 39  
earpiece, 9, 35  
key beep, 35  
ringer, 35  
W
wallpaper, 39  
web browser, 51  
World Clock, 47  
silent mode, 7, 34  
speakerphone  
turning off, 9  
turning on, 9  
stopwatch, 47  
symbol mode, 22  
T
technical support, 53  
text entry, 21  
quick reference, 23  
text messages, 24  
time format, 39  
timer, 47  
timing calls, 12  
Tip Calculator, 46  
TTY/TDD, 41  
U
unlocking the phone, 40  
56  
Index  
 
 
 

KTM Motorcycle 85SX User Manual
Kustom Stereo Amplifier KGA16 User Manual
LevelOne Network Router WBR 3403TX User Manual
LG Electronics Computer Monitor W2600V PF User Manual
LG Electronics Washer 102205FDBN User Manual
Linear Medical Alarms PERS 2400B User Manual
Logitech Clock Radio S400i User Manual
Macrom Portable DVD Player M DVD902RV User Manual
Makita Saw 7301 User Manual
MartinLogan Portable Speaker ESL Speaker User Manual