Life Fitness Exercise Bike LC85R User Manual

([HUFLVHꢀ%LNH  
$ 6 6 ( 0 % / < ꢀ , 1 6 7 5 8 & 7 , 2 1 6  
 
IMPORTANT SAFETY INSTRUCTIONS!  
DO NOT locate the Recumbent Exercise Bike outdoors, near swimming pools, or in areas of high  
humidity.  
DO NOT operate your Recumbent Exercise Bike if it has been dropped, damaged, or even partially  
immersed in water. Contact Life Fitness Customer Support Services at the number in the Operation  
Manual.  
DO NOT locate the Recumbent Exercise Bike any closer than 30 inches (76 cm) to a television set.  
DO NOT locate additional Recumbent Exercise Bike any closer than a minimum of 42 inches (107  
cm) from center to center to avoid interference (cross talk) between Heart Rate monitors.  
DO keep the area around your Recumbent Exercise Bike clear of any obstructions, including walls  
and furniture.  
DO verify the contents of the delivery carton against the accompanying Parts Listing prior to setting  
the cartons and shipping material aside. If any parts are missing, contact Life Fitness Customer  
Support Services at the number listed in the Operation Manual. Save the shipping cartons in case of  
return.  
DO read the entire Operation Manual prior to attempting to operate this machine as this is essential  
for proper use.  
NE PAS placer le vélo d’exercice allongé Lifecycle à l’extérieur, près d’une piscine ou dans un  
endroit très humide.  
NE PAS faire fonctionner le vélo d’exercice allongé Lifecycle s’il est tombé, s’il a été endommagé ou  
s’il a été partiellement plongé dans l’eau. Téléphoner au service après-vente de Life Fitness dont le  
numéro figure sur la couverture arrière du guide d’installation.  
NE PAS placer le vélo d’exercice allongé Lifecycle à moins de 76 cm (30 po) d’un poste de  
télévision.  
MAINTENIR la zone autour du vélo d’exercice allongé Lifecycle libre de toute obstruction, y compris  
murs et meubles.  
VÉRIFIER si lemballage contient toutes les pièces de la liste jointe avant de le mettre de côté. Si  
des pièces manquent, téléphoner au service après-vente de Life Fitness dont le numéro figure sur la  
couverture arrière du guide dinstallation. Conserver lemballage au cas où lappareil devrait être  
renvoyé.  
LIRE le manuel de lutilisateur tout entier avant dessayer de faire fonctionner cet appareil. Ceci est  
indispensable à son utilisation correcte.  
 
TOOLS REQUIRED FOR ASSEMBLY...Phillips screwdriver, 3/16" hex key wrench, T-40 Torx wrench  
PARTS DESCRIPTION  
1
3
Seat Back Screw  
0017-00101-1131  
Qty: 4  
Qty: 4  
Qty: 1  
Qty: 1  
Qty: 1  
Qty: 1  
2
4
6
8
Seat Back Washer  
0017-00104-0253  
Qty: 4  
Qty: 4  
Qty: 1  
Qty: 1  
Qty: 1  
Console Support Assembly Bolt  
0017-00101-1737  
Console Screw  
0017-00101-1253  
5
Seat Back  
Console Support Assembly  
AK39-00003-0000  
7
Display Console  
Left Pedal Strap  
Accessory Tray Assembly (If so equipped)  
9
10 Right Pedal Strap  
11  
9V Battery (Model 8500 Only)  
0017-00003-0757  
1
2
3
4
1”  
2”  
3”  
4”  
5”  
 
7
11  
8
4
6
9
5
3
2
1
10  
 
1. Slide the ACCESSORY TRAY (#8) (if so equipped) over the  
user right seat back post and down to make contact with the  
SEAT HANDLEBAR.  
2. Position the underside clamp bracket (A) around the SEAT  
HANDLEBAR and tighten the two clamp SCREWS and  
WASHERS (B).  
NOTE: BE CAREFUL NOT TO OVER-TIGHTEN  
THE SCREWS.  
MISE EN GARDE : VEILLER À NE PAS TROP SERRER  
LA VIS.  
3. Align the four holes in the SEAT BACK (#5) with those in the  
SEAT BACK POSTS. Insert the four SCREWS (#1) and  
WASHERS (#2) through the backside of the SEAT BACK  
POSTS and into the SEAT BACK. Tighten the four SCREWS  
with a hex key wrench.  
NOTE: BE CAREFUL NOT TO OVER-TIGHTEN  
THE SCREWS.  
MISE EN GARDE : VEILLER À NE PAS TROP SERRER  
LA VIS.  
4. Unfold the CONSOLE WIRE HARNESSES (C) from the POST  
extending from the FRAME.  
5. Feed the WIRE HARNESSES at the top of the FRAME POST  
through the bottom of the CONSOLE SUPPORT ASSEMBLY  
COLUMN. Continue pushing the WIRE HARNESSES until the  
CONNECTORS at the end of the WIRE HARNESSES exit  
through the opening at the top of the COLUMN. Gently pull the  
WIRE HARNESSES to remove the slack.  
7
6. Position the CONSOLE SUPPORT ASSEMBLY (#6) so that  
the HANDLEBAR is facing the user and slide the CONSOLE  
SUPPORT ASSEMBLY into the FRAME POST (D), being  
careful not to pinch the WIRES in the process. Align the holes  
in the top of the CONSOLE SUPPORT ASSEMBLY with those  
in the FRAME POST. Install the four CONSOLE SUPPORT  
ASSEMBLY BOLTS (#3) to secure it into position. Tighten the  
four CONSOLE SUPPORT ASSEMBLY BOLTS to 15-20 ft.  
lbs.  
4P  
F
10P  
11  
E
6
NOTE: BE VERY CAREFUL NOT TO DAMAGE THE WIRES  
WHEN PASSING THE BOLTS THROUGH THE HOLES.  
TIGHTEN THE BOLTS SECURELY.  
MISE EN GARDE :FAITES ATTENTION TRÈS À NE PAS  
ENDOMMAGER LES FILS EN PASSANT LES BOULONS  
PAR LES TROUS. SERREZ LES BOULONS SOLIDEMENT.  
4
7. Align the LOCKING TABS of the 10-PIN CONNECTOR and  
the 4-PIN CONNECTOR (Models 9500HR) and plug them  
together until they SNAP into place.  
C
3
8. Model 8500 Only  
Remove the BATTERY DOOR (E) located on the back of the  
DISPLAY CONSOLE (#7). Carefully pull the BATTERY WIRE  
HARNESS (F) out of the BATTERY COMPARTMENT. Plug  
the BATTERY (#11) into the BATTERY WIRE HARNESS  
CONNECTOR. Carefully place the BATTERY and BATTERY  
WIRE HARNESS into the BATTERY COMPARTMENT.  
Replace the BATTERY DOOR.  
D
 
9. Carefully feed the wires back into the top of the CONSOLE  
SUPPORT ASSEMBLY (#6) and attach the DISPLAY  
CONSOLE (#7) to the CONSOLE SUPPORT ASSEMBLY  
using the four CONSOLE SCREWS (#4) and a Phillips  
screwdriver. Tighten the four SCREWS in a criss-cross  
pattern.  
H
NOTE: BE CAREFUL NOT TO OVER-TIGHTEN  
THE SCREWS.  
MISE EN GARDE : VEILLER À NE PAS TROP SERRER LA  
VIS.  
G
J
10. After placing the exercise bike in the intended location for use,  
check the stability of the bike. If the exercise bike is not level,  
turn a LEVELER (G) in the rear STABILIZER BAR (H) in either  
direction until the rocking motion is eliminated. Tighten the  
JAM NUT (J) when the exercise bike is level.  
10  
NOTE: ONLY ONE LEVELER NEEDS TO BE TURNED.  
REMARQUE : NE TOURNER QUUN SEUL VÉRIN.  
11. Locate the RIGHT PEDAL STRAP (#10) marked with an R.  
Attach the RIGHT PEDAL STRAP to the RIGHT PEDAL (K)  
with the double slot on the inward pedal strap tab looping  
upward and attaching to the outward pedal strap tab. Repeat  
for the LEFT PEDAL STRAP (#9) marked with an L.  
K
 
PRE-OPERATION CHECKLIST  
Ensure that the console support screws are tight.  
Make sure the Recumbent Exercise Bike is properly leveled and stable.  
Ensure that the Leveler Jam Nuts are tight.  
Read the entire Operation Manual before using the Recumbent Exercise Bike.  
Before attempting to operate your Recumbent Exercise Bike, it is imperative that you familiarize yourself  
with the contents of the Operation Manual. If your Recumbent Exercise Bike does not respond as  
described in the OPERATION MANUAL, contact the nearest Life Fitness service center as listed in the  
Operation Manual.  
© 2002 Brunswick Corporation. All rights reserved. Life Fitness is a trademark of Brunswick Corporation.  
Polar is a registered trademark of Polar Electro, Inc.  
M051-00K20-A327  
8/02  
 

LG Electronics DVD Player BD390 User Manual
LG Electronics Flat Panel Television W ZB User Manual
Life Fitness Treadmill T9 0XXX 04 User Manual
Linear Home Security System DF 31 EC User Manual
Linksys Network Router UWAG200G User Manual
Lucent Technologies Answering Machine AS60 User Manual
Madge Networks Computer Hardware 80211B 95 20 User Manual
Marvel Industries Beverage Dispenser 6SWCE User Manual
McCulloch Lawn Mower MCM2011 User Manual
Melissa Mixer 646 061 User Manual