Logan Graphic Products Sander F200 2 User Manual

Model F200-2  
Instruction Manual  
PICTURE FRAMING  
Precision  
SANDER Elite  
Description  
The Model F200-2 Precision Sander Elite has been designed to improve saw cut miters  
to perfect 45˚. A new 10” diameter wheel can accommodate most moulding sizes. After  
sanding the miters, the result is a sharp seamless frame corner that is of professional  
quality. The Model F200-2 Precision Sander Elite is a precision tool and will give many  
years of service. Producing professional quality picture frames is now easier than ever!  
847-526-5515  
Purchase Date  
 
Model F200-2  
Instruction Manual  
Precision SANDER ELITE  
Operation  
Preparation  
1. Rotate alignment bar to either side  
by lifting and turning (Fig. 3)  
Sanding  
Fig. 3  
1. Place back of moulding against  
alignment bar with finish side up.  
2. Slide moulding against wheel.  
3. With one hand, hold moulding firmly  
against alignment bar and wheel.  
With other hand, rotate wheel  
in the direction of the moulding  
or downward onto the top of the  
moulding.  
(Figs. 4a and 4b)  
4. Rotate wheel 4-6 times.  
• Adjust the pressure against  
the wheel while rotating. Start  
with light pressure until wheel  
is spinning, then increase the  
pressure for easier sanding.  
Fig. 4b  
Right Side  
Fig. 4a  
Left Side  
5. Check sanded surface of moulding  
to see if surface is smooth.  
6. Repeat until full surface is smooth.  
Check Lengths It is important both sides of  
moulding are same length for square frame  
and seamless corners.  
1. Lay two moulding pieces side-by-  
side so miters are facing up.  
2. Align the two lower edges.  
3. Check to see if the upper edges are  
Fig. 5  
Check top  
even in length (Fig. 5).  
4. If not, sand longer piece until it’s  
even with short piece.  
Moulding  
Pieces  
Align Bottom  
3
Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 www.logangraphic.com  
 
Instruction Manual  
Precision SANDER ELITE  
Model F200-2  
Cleaning  
Fig. 6  
1. Hold the cleaning bar at 45 degrees and move down the length of  
the wheel while rotating (Fig. 6).  
2. Use light pressure. NOTE: Surface of sandpaper may not look clean  
but it is. The dust sticks to the backing material not the raised  
abrasive grit.  
Adjustment 45°  
1. Remove sand paper  
2. Place the 45˚ square flat against the wheel and up against bar  
(Fig. 7). Look for gaps against the bar.  
3. Adjust the bar using adjustment wrench until gap disappears.  
Fig. 7  
Changing Disk Paper  
45° Triangle  
1. Remove disk using disk wrench.  
2. Remove worn sandpaper and clean surface of disk of any glue or  
debris using a razor blade or mineral spirits.  
3. Peel off adhesive backing and apply sandpaper  
to disk carefully. Press thoroughly to remove any bubbles.  
Trouble Shooting  
Problem  
Solution  
Moulding splinters.  
Reverse sanding direction.  
Apply less pressure to surface being sanded.  
Not producing 45 degree angle.  
Refer to instructions for making adjustments using micro-adjustment blocks. Only small incre-  
mental adjustments are required.  
Remove any debris between moulding and fence.  
Remove any debris between fence and micro-adjustment stop(s).  
Make sure center bolt on sanding wheel is tight.  
Clean sanding disk with supplied cleaning bar.  
Replace sand paper disk.  
Rough surface after sanding.  
Gaps appear in moulding joints.  
Apply less pressure to surface being sanded.  
Sand surface until a fine line of dust appears across the top of the moulding.  
Warranty  
Logan Graphic Products, Inc. (“Logan”) warrants the Precision Sander Elite - Model F200-2, to be free from defects in parts and workmanship for a period of one  
year from the date of original purchase. Logan warrants that it will either repair or replace, at its’ sole discretion, any necessary replacement parts found to be  
defective. Should the product need to be returned to Logan for repair or replacement parts, authorization for any return must come from Logan in writing. Costs of  
returning the product to Logan, including insurances, shall be borne by the purchaser. Logan shall not be liable for any damages or losses, incidental or consequen-  
tial, direct or indirect, arising from the use of this product. This warranty extends only to the original purchaser and is not assignable or transferable. This warranty is  
in lieu of all other warranties, expressed or implied.  
Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 www.logangraphic.com  
L689N2 1/10  
 

La Crosse Technology Weather Radio 30B 1425B User Manual
La Crosse Technology Weather Radio WS 9117U User Manual
Lanzar Car Audio Stereo Equalizer XE3 User Manual
Lennox International Inc Air Conditioner 15CHAX Series User Manual
LG Electronics Cell Phone 5450 User Manual
LightSpeed Technologies Speaker DRQ User Manual
Loewe Flat Panel Television A 32 HD+ 100 User Manual
Martin Audio Stereo Amplifier MA52K User Manual
Maxxsonics Speaker DWH 252 User Manual
Maytag Clothes Dryer YMED6000XG0 User Manual