Magnadyne Automobile Alarm X9 User Manual

Owner’s  
Manual  
Model: X9  
For Technical Assistance, please call (800) 638-3600,  
 
Remote Control Transmitters  
The LCD screen on the 2-way remote control displays graphic icons. It provides visual information  
on any trigger of the sensors and around the clock surveillance of your vehicle, as well as  
displaying the present status of the system.  
4
4
SAVE  
2-Way LCD Remote  
LCD Display Icons  
1-Way Remote  
LCD Remote Icons  
Door Lock  
Vehicles Doors are Locked  
Timer Control Start  
Automatic Engine Start (Timed)  
Power Save Mode  
Saves The Battery Power when  
Transmitter is not in Use  
Door Unlock  
Vehicles Doors are Unlocked  
Armed Mode  
Security System is Armed  
Vibrate Mode  
Vibrates when Security System is  
Triggered  
Valet Mode  
Security System is Disarmed  
Low Battery  
Replace the Transmitter Battery  
Remote Transmission  
Transmitting a Signal  
Shock Sensor  
Shock Sensor Triggered  
In-Range Indicator  
You are within Remote Control Range  
Ignition  
Engine Starting by Remote Control  
Door Triggered  
Doors are Opened (Zone 3)  
Ignition  
Trigger On Ignition Switch (Zone 5)  
Trunk/Hood Triggered  
Trunk/Hood are Open  
Engine Running  
Vehicle Engine is Running  
Warn Away  
Shock Sensor Triggered (Zone 1)  
Driver Paging / Lost and Found  
Someone is Paging you from the Vehicle  
Second Vehicle  
Communicate with a Second Vehicle’s  
Security System  
System Trigger/Panic  
Alerts that the System has been  
Triggered  
3
 
Transmitter Operation  
Transmitter Button  
System Function  
Remark  
Lock Doors & Arms System  
Arm and Delete the 2-Stage  
Shock Sensor  
Press Twice within 3 Seconds  
Press within 3 Seconds  
Upon Armed  
-
-
Arm System and  
Hidden Alarm Function  
Car Locator  
Panic Function  
Press and Hold for 3 seconds.  
Ignition in “OFF” Position  
Silent Arming/Disarming  
Active Anti-Car Jacking Mode  
+
+
Ignition in “ON” Position,  
Press and Hold for 2 Seconds  
Unlock Doors & Disarm System  
Two Steps Door Unlock and  
Disarm System  
-
Press Twice within 3 Seconds  
Press and Hold for 1.5 Seconds  
Trunk Release - Channel 3  
Passive Arming Bypass  
While the System  
is in “Disarmed” Mode  
-
-
Activate or Turn Off  
the Remote Start  
Press Twice within 3 Seconds  
Channel #4 Timer Control Output  
+
-
Turbo Timer Mode  
Press Once on 1-Way Remote  
Second Vehicle System Control  
(Hold)  
+
See Page 17 of this Manual for  
More Details  
Enter/ Exit Second Vehicle System  
Control using the LCD Transmitter  
Then  
(Hold)  
4
 
LCD Remote Programming  
Vibration/Melody Mode  
This mode is useful when you are in a noisy place and it is difficult to hear the beep from the  
transmitter. While in the Vibration/Melody Mode, the transmitter will vibrate if your security  
system has been activated.  
1. Press and hold the  
and buttons at the same time until one long beep is  
heard. Programming has now been entered.  
2. Within 5 seconds, press the button to toggle between “ON” or “OFF”. The  
icon will be displayed in the LCD display when the Melody Mode is On.  
3. To exit the Programming Mode, take no action for five seconds. The remote  
control will generate two long beeps to indicate Programming Mode has been  
exited.  
Power Save Mode  
While in the Power Save Mode, the LCD remote transmitter will “Sleep” until a  
button is pushed, extending the life of battery. When Power Save Mode is “OFF”,  
the remote control will wake up periodically to check for messages from the  
security system.  
1. Press and hold the  
and  
buttons at the same time until one long beep is  
heard. Programming has now been entered.  
2. Within 5 seconds, press the  
button to toggle between “ON” or “OFF”. The  
remote will beep once for “ON”, and twice for “OFF”. When Power Save Mode is “ON”, the  
icon on the LCD screen indicates entry into Power Save Mode.  
3. To exit Programming Mode, take no action for five seconds. The remote control will generate  
two long beeps indicating Programming Mode has been exited.  
Screen Lamp On  
Press the button once, and the LCD screen lamp will turn on for 5 seconds.  
System Status Check  
To check the system’s present status through the LCD screen, press the  
transmitter button first, then within 3 seconds press  
and buttons at the  
same time. The response will be one melody sound, and the LCD screen will be  
illuminated. Note: If no response is received, then you are out of range.  
Clear the Flash Icon and Melody Sound  
Press the  
button first, then within 3 seconds press the and buttons at the  
same time. These steps will clear the flash icon and melody sound on the LCD  
transmitter.  
Stop the Trigger Melody Sound  
While triggering the alarm the LCD screen will alert the user through a melody sound and a  
flashing trigger icon. Press any button on the LCD transmitter to stop melody sound only, and the  
remote control will not send a command to the system.  
5
 
LCD Remote Programming  
Press Buttons at the Same Time: Then Press Button Within:  
System Function  
Switching to 2nd Vehicle  
or Returning to 1st  
Vehicle Operation  
+
5 Sec.  
+
+
Melody / Vibration Mode  
Power Save Mode  
5 Sec.  
5 Sec.  
LCD Screen Lamp  
Turns On for Five Seconds  
+
+
System Status Check  
3 Sec.  
3 Sec.  
Clear the Flash Icon  
and Melody Sound  
(Applies to LCD Transmitter Only)  
Battery Replacement  
The LCD remote control is powered by a 1.5 Volt AAA  
Alkaline battery. When the power of the battery  
weakens the battery icon  
will be displayed on the  
screen. When the old battery is replaced with a new  
one, there will be a beep to indicate the power is up. To  
replace the battery, follow the steps in the illustration  
at left.  
Note: Press the button two times when the battery  
compartment is empty, then insert the new battery.  
Interference  
The transmission range may decrease if the system encounters interference from tall structures or  
stronger radio frequencies such as high-voltage power lines.  
LED Indicator  
LED  
Function  
OFF  
System is Disarmed  
System is Armed  
System in Automatic Arming  
Slow Flashing  
Fast Flashing  
1 Flash Every 5 Seconds System in Valet Mode (Ignition Key On or Off)  
2 Flashes - Pause  
3 Flashes - Pause  
4 Flashes - Pause  
5 Flashes - Pause  
Zone 2, Trigger on Trunk/Hook  
Zone 3, Trigger on Door Switch  
Zone 4, Trigger on Shock Sensor  
Zone 5, Trigger on Ignition Switch  
6
 
Parking Light Indicators  
Flash  
Function  
1 Flash  
System is Armed  
System is Disarmed  
Disarmed / Triggered  
Car Locator  
2 Flashes  
3 Flashes  
3 or 6 Flashes  
Constant On or Flashing Under Remote Start  
Chirp Indicators  
Chirp  
Function  
1 Chirp  
System is Armed  
System is Disarmed  
Ajar Warning  
2 Chirps  
3 Chirps  
4 Chirps  
2,3,6 Chirps  
Disarm / Triggered  
Progressive Car Locator  
System Characteristics  
Parking  
Light  
Siren/Horn  
LED  
Doors  
Starter  
Dome Light  
Disabled  
(Option)  
1. Arming  
1 or 3 Chirps  
1 Flash  
Slow Flash  
Locking  
2 or 3  
Flashes  
Turns on for  
30 Seconds  
2. Disarming 2 or 4 Chirps  
Unlocking  
Disabled  
(Option)  
3. Trigger  
4. Panic  
Alarming  
Alarming  
Alarming  
Flashes  
Flashes  
Flashes  
Slow Flash  
Flashes  
Flashes  
Flashes  
5.Car  
Jacking  
Disabled  
(Option)  
6.Car  
Locator  
2,3,6 Chirps 3,6 Flashes  
7
 
Manual Lock/Arm  
1. Press the button on the transmitter.  
2. The siren will chirp once and parking lights will flash once indicating that the system is now  
armed. The vehicle door will lock upon arming when interfaced with the security system.  
System Armed  
Door Ajar  
Trunk/Hood Ajar  
Ajar Warning:  
If the siren sounds 3 chirps,  
then you have left a door,  
trunk, or hood lid ajar.  
Silent Arming/Disarming  
Press the transmitter and button at the same time to arm or disarm your security system. No  
chirp sound will be heard. The arm/disarm confirmation will be through the vehicle’s parking  
lights only.  
Shock Sensor Bypass  
Press the button on the transmitter two times within 3 seconds. This will arm the security  
system and bypass the shock sensor. The system will chirp one additional time to confirm the  
sensor Bypass Mode was activated. The sensor bypass feature is programmed to activate for one  
arming cycle only. The security system will return to normal operation during the next arming  
cycle.  
Hidden Alarm Function  
Press the  
button first, within 3 seconds press the  
button to activate the hidden alarm  
function. The security system will arm, but the siren / horn will be silenced even if the sensor is  
triggered in the armed status.  
Automatic Arming  
Manual arming/disarming is controlling your security system via the remote transmitter. This  
security system is equipped with an optional Automatic Arming feature which allows the security  
system to arm 30 seconds after the last door is closed. Operation is as follows:  
1. Turn the ignition to the “OFF” position and exit the vehicle.  
2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you  
reopen any Door, Hood, Trunk the security system LED will stop flashing. It will begin flashing  
again once the vehicle’s entrances are closed.  
3. After the 30-second timer has elapsed, the security system will automatically “ARM”. The  
siren/horn will chirp once, and the parking lights will flash once.  
Automatic Arming with Automatic Door Locking (Programmable)  
The vehicle doors will automatically lock after the passive arming cycle has been completed.  
8
 
(Continued)  
Automatic Arming  
Automatic Arming Bypass  
While the system is in Disarmed Mode, press the  
button twice. The horn/siren will respond  
with one chirp and the LED will turn “ON”. The security system will remain in this mode for as  
long as you wish. To exit this mode press the or buttons and the system will return to normal  
status.  
Manual Un-Lock / Disarm  
1. Press the button on the transmitter.  
2. The siren will chirp twice and parking lights will flash twice indicating that the system is now  
disarmed. The vehicle door will unlock and the dome light will turn on for 30 seconds upon  
disarming when interfaced with the security system.  
System Disarmed  
Doors Triggered  
Trunk/Hood Triggered Shock Sensor Triggered Ignition Triggered  
Tamper Disarming  
If the security system is triggered upon disarm, the siren will chirp 4 times and the parking lights  
will flash 3 times.  
Pathway Illumination  
This feature turns the parking lights “ON” for 30 seconds upon a unlock signal and for 10 seconds  
upon the lock signal.  
Two Step Door Unlock  
This feature will independently unlock the driver’s door only when disarming the security system.  
Pushing the button a second time within 3 seconds will unlock the other doors.  
Automatic Rearm  
If this feature is selected, the security system will automatically rearm itself within 60 seconds  
after disarming with the remote transmitter. Automatic rearm will cancel if any door is opened  
before the 60 second timer is up.  
Disarming without a Transmitter  
The override function may be used if the remote transmitter is lost or inoperative. Override can be  
done without password/pin number (this is the factory default setting).  
1. Enter the vehicle and turn the ignition switch to “ON” position (alarm will sound).  
2. Within 10 seconds push and release the valet switch. The alarm will stop sounding and enter  
the Disarm Mode. You can now start and operate the vehicle normally.  
9
 
(Applies to All Transmitter Types)  
RF Valet Mode  
RF valet mode provides the same functions as manual valet mode but allows you to enter and exit  
the valet mode using the remote transmitter. When the system is in Valet Mode, all alarm  
functions and remote start functions are off. However, the remote panic feature and remote door  
locks remain operational. To enter/exit the RF Valet Mode, repeat the following procedures.  
Enter Valet Mode  
1. In the Disarmed Mode, turn the ignition to “ON” position and open the drivers door.  
2. Push and hold the and  
transmitter buttons until the door locks cycle “Lock then Unlock”.  
The LED will flash every 5 seconds to indicate that the unit is in the Valet Mode.  
Note: When the unit is in valet mode, the LCD transmitter  
icon will be displayed  
Exit Valet Mode  
1. To return to normal operation, turn “ON” ignition.  
2. Push and hold the and  
transmitter buttons until the door locks cycle “Lock then Unlock”.  
The LED will stop flashing every 5 seconds to indicate that the unit is out of the Valet Mode.  
Progressive Remote Vehicle Locator System  
Note: The remote vehicle location system is active 30 seconds after the alarm is armed.  
1. Press the  
button to active the vehicle locator system. The horn/siren will beep 2 times and  
the parking lights will flash 3 times. This operation will repeat a second time.  
2. Press the button again within 30 seconds. The horn/siren will beep 3 times and the parking  
lights will flash 3 times. This operation will repeat a second time.  
3. Press the button again within 30 seconds. The horn/siren will beep 6 times and the parking  
lights will flash 6 times.  
Manual Valet Mode  
Manual valet mode allows you to bypass all alarm functions eliminating the need to hand your  
transmitter to parking attendants or garage mechanics. This mode is also a necessity if your  
transmitters become in-operable. When the system is in Valet Mode, all alarm functions and  
remote start functions are off. However, the remote panic feature and remote door locks remain  
operational. To enter the Manual Valet Mode, the system must first be disarmed either by using  
your remote transmitter, or by operating the manual override sequence.  
Enter Valet Mode  
1. When in Disarmed Mode, turn the ignition to the “ON” position.  
2. Push and hold the valet switch for 2 seconds. The LED will flash every 5  
seconds as long as the unit is in the Valet Mode.  
Note: When the unit is in valet mode, the LCD transmitter  
displayed  
icon will be  
Hold 2 Seconds  
Exit Valet Mode  
1. To return to normal operation, turn “ON” ignition.  
2. Push and hold valet switch for 2 seconds. The LED will stop flashing, indicating the system has  
now exited the Valet Mode.  
Note: When the unit is out of valet mode, the  
icon will be off.  
10  
 
Panic Feature  
The transmitter can be used as a remote panic switch to manually trigger the alarm system in  
case of an emergency.  
1. Press and hold the button for 3 seconds to enter the Panic Mode (horn/siren will start to  
sound and parking lights will flash).  
2. While in Panic Mode the transmitter and buttons can be used to lock and unlock the door  
(if that option is installed). However, if the  
button is pressed, the vehicle’s starter disable  
device (when installed) will be disabled, allowing the vehicle to start.  
3. To turn off the panic function, press and hold the or button again for 3 seconds.  
Note: If any transmitter buttons other than or button is pressed the panic function will be  
turned off.  
4. If the panic function is not turned off by the transmitter, it will turn off and reset itself after 30  
seconds.  
Domelight Supervision  
The Security System has a unique feature for using your vehicle’s dome light:  
1. Upon disarming the vehicles security system, the interior dome light will remain on for 30  
seconds.  
2. If the security system is triggered, the dome light will flash for the same duration as the  
horn/siren.  
Note: Turn “ON” the ignition switch or arm the system to turn off the dome light.  
Ignition Key Controlled Door Lock/Un-Lock  
If the vehicles door locks have been interfaced with the security system, the system will  
automatically lock the doors when the ignition is turned “ON”, or unlock the doors when ignition  
key is turned “OFF”.  
Channel #3 Trunk Release Output  
Press and hold the  
button for two seconds to activate the trunk release (Channel 3 output)  
and/or any other devices connected.  
Channel #4 Timer Controlled Output  
Press and hold the  
and  
button at the same time to activate the Channel 4 output. Channel 4  
is user programmable timer output. You may program the built-in timer to send a ground signal  
for any time duration from 1 second to 120 seconds. For example, this timer output may be used  
to turn on the headlights, power window or sunroof (Factory defaults setting at momentary  
output.)  
11  
 
Anti-Carjacking Feature  
Warning: This security system has a car jacking feature. Its default setting is “OFF”. So be sure to  
enable this feature if you feel it is needed.  
Active Anti-Car Jacking  
1. Press and hold the transmitter  
and  
buttons at the same time for 2 seconds while the  
vehicle’s ignition is “ON”. The parking lights will turn on for 1.5 seconds to indicate the system  
has entered the Anti-Car Jacking Mode.  
2. Once the system is armed in the Anti-Car Jacking Mode, the system will trigger when the door  
is opened and closed while the ignition is “ON”.  
Passive Anti-Car Jacking  
1. Turn the ignition switch to the “ON” position, and the system will enter the Anti-Car Jacking  
Mode.  
2. Once the system is armed in the Anti-Car Jacking Mode, the system will trigger when the door  
is opened and closed while the ignition is “ON”.  
When the Anti-Car Jacking Feature is Triggered  
A. 50 seconds after the system has been triggered. The siren will start chirping for 15 seconds.  
B. During this 15 second period of chirping, you can push the valet switch once to turn off the car  
jacking feature.  
C. 65 seconds after the system has been triggered. The siren starts sounding and the parking  
lights start flashing.  
D. 90 seconds after the system has been triggered:  
1. The siren will still be sounding and the parking lights flashing.  
2. The starter disable will activate to prevent the vehicle from starting.  
3. Anti-Car Jacking Mode will remain active until the override procedure is performed or the  
vehicle's battery power is exhausted.  
Override the System to Turn Off Anti-Car Jacking  
Turn the ignition switch from OFF to ON, and within 10 seconds push the valet switch. The siren  
will stop sounding and the security system is now disarmed.  
Note: If you use password pin code to double protect the vehicle, you will need to use it to  
completely disarm the system.  
(Applies to LCD Transmitter Only)  
Driver Paging / Lost and Found  
Driver Paging / Lost and Found is useful the event that someone wants to page  
the driver of the parked vehicle, or someone cannot find the LCD transmitter.  
With the ignition switch in the “OFF” position, press and hold the valet switch for  
2 seconds to page the driver. One chirp shall be emitted and the paging melody  
continues sounding from the LCD transmitter and  
will flash on the screen.  
12  
 
Out of Range Indication  
If the Out-of-Range Indication feature is activated the system will automatically check the range  
every 30 minutes after armed.  
1. If the user is within the range, the icon will display on the LCD screen.  
2. If user is out of range, the  
beeps 5 times.  
icon will disappear from the LCD screen and the transmitter will  
Note: Activating this feature will decrease the life expectancy of battery.  
13  
 
REMOTE START OPERATIONS  
Activate  
Remote Start  
Remote Start Your Vehicle Using the Remote Transmitter  
1. Press the button twice on the transmitter.  
2. The parking lights will turn on indicating the remote start has received the  
signal (A melody sound from your LCD transmitter and the  
flash on the LCD screen to confirm the remote start was activated.)  
3. The engine will start in approximately 5 seconds.  
icon will  
4. Once the engine is running, the parking lights will turn on again after a few  
seconds, and the climate controls will activate and adjust the vehicles  
interior temperature to your preset setting. While the vehicle is running, the  
icon will flash on the LCD screen indicating the count down timer based on  
the 5, 10, 20 or 30 minute run-time setup by the installer.  
5. The vehicle will run for 5 to 30 minute cycles and automatically shut down.  
(When the unit shuts off, the count down timer will turn off and the  
transmitter will play a melody).  
Engine  
Running  
Note: The Remote Start Unit will not start the vehicle if any one of the  
following  
conditions exists:  
1. The hood is opened.  
2. The brake pedal is pressed.  
3. Move the optional remote start enable toggle switch to OFF position (if installed).  
4. The vehicle is in a gear other then “Park” or “Neutral”.  
(Child Safety Mode)  
Safe Start Mode  
If the default method of remote starting has been reprogrammed to Child Safety Mode Operation,  
to remote start your vehicle is to press the and the buttons at the same time.  
Note: To turn off the remote start press the and the buttons at the same time.  
Vehicle Operation when Running in Remote Start Mode  
1. Insert the ignition key, and turn it to the “ON” position, NOT the “START” position.  
2. Press the brake pedal.  
Note: If the brake pedal is pressed before the key is in the “ON” position, the engine will  
automatically shut off.  
Temporary Stop Feature  
This feature allows the vehicle to remain running after the key has been removed from the  
ignition. It is useful on occasions when you wish to exit and lock the vehicle for a short period of  
time, but keep the engine running allowing the climate controls to stay on.  
1. Before turning the engine off with the ignition key, press the  
three times indicating the feature has been activated.  
button twice. The LED will flash  
2. Turn the ignition key to the “OFF” position (the engine will stay running).  
3. The engine will run until the pre-programmed time has elapsed or shutdown input is received.  
14  
 
Timer Starting Mode  
Important! Timer Start should be used only in open areas. Never start or leave a vehicle running in  
an enclosed area such as a garage or carport.  
This unit can be programmed to auto-start and run the engine every 2 or 3 hours (3 hours is the  
default setting). The engine will run for the programmed run time and then shut down. This  
feature is designed to prevent the engine from freezing in cold climates.  
A Maximum of Six Auto-Start Cycles can Occur.  
Timer Starting  
Enter Timer Start:  
1. Press the button twice to remote start the vehicle.  
2. As soon as the parking lights have turned on or are flashing, press the  
press and hold the button. The parking light will flash 3 times, the siren or  
horn will chirp 3 times and the icon will appear on the LCD display. The  
button once. Then  
vehicle is now programmed to start every 3 hours.  
3. Press the brake pedal to shut off the engine.  
Exit Timer Start:  
1. Make sure the remote start system is not operating the engine.  
2. Turn the ignition “ON”. The LED and parking lights will flash 4 times. The horn  
chirps 4 times. The vehicle is no longer programmed to Timer Start  
automatically.  
Or  
1. Press the button twice to remote start the vehicle.  
2. As soon as the parking lights have turned on or flashing, press the button once. Then press  
and hold the button. The parking lights will flash 4 times. The siren or horn chirps 4 times.  
The vehicle is no longer programmed to Timer Start automatically.  
Turn Off Remote Start System  
When the engine is running by remote start and you wish to shut it off, follow  
these steps:  
1. While in Remote Start Mode, press the  
transmitter.  
button twice on the remote  
2. Move the optional remote start toggle switch to the “OFF” position (if  
installed).  
3. Press the vehicle’s brake pedal, the engine will stop running and the parking  
lights will turn off to indicate the engine has been shut off.  
(If Installed)  
Toggle Switch Disable  
The disabling the Remote Start System feature allows your system’s remote start unit to be  
temporarily disabled, which prevents the vehicle from being remote started accidentally. This is  
useful if the vehicle is being serviced or stored in an enclosed area. To disable the remote start,  
move the optional remote start enable toggle switch to the “OFF” position.  
15  
 
Turbo Timer Mode  
After arriving at your destination, Turbo Timer keeps the engine running for a programmable time  
period of 1, 3 or 5 minutes. This allows the engine’s turbo charger time to conveniently cool down  
after you have left the vehicle.  
To Activate:  
1. While the engine is running, set the emergency brake and place the transmission into "Park".  
2. Before turning off the engine, press and release and buttons at the same time. The parking  
lights will flash indicating the remote start has entered Turbo Timer Mode.  
3. Remove the ignition key and the engine will keep running.  
4. Exit and secure the vehicle. The engine continues running until the pre-programmed time has  
elapsed.  
Remote Start Shutdown Inputs  
If any of the following conditions exist while the system is operating, the engine will not start or will  
shut down immediately:  
1. The hood is opened.  
2. The brake pedal is pressed.  
3. The hand brake is released (for Standard Transmission vehicles only).  
4. Engine is over-revved (Tachometer Checking Type only).  
5. The preprogrammed run time (5/10/20/30 minutes) has elapsed.  
6. Press the  
button twice on the remote transmitter under Remote Start Mode.  
7. Move the optional remote start enable toggle switch to “OFF” position (if installed).  
8. The vehicle refused to start running after 3 unsuccessful attempts.  
16  
 
Second Security System Operation  
If your transmitters have been programmed to a second Marksman security system, follow the  
steps below.  
For 1-Way Remote Control Transmitter:  
1. First press the button on the transmitter.  
2. Once the  
button is pressed, the LED on the transmitter will illuminate for 3 seconds to  
indicate second vehicle transmitter operation.  
3. While the LED is illuminated, press any button on the transmitter to control the second vehicle’s  
security system or alarm function (arm/disarm/trunk/remote start).  
Note: Button functions are the same for the second car as they are for the first car.  
For LCD Remote Control Transmitter:  
Second Vehicle Operation: While the  
can remote control and communicate with a second vehicle security system.  
1. Press and hold and buttons at the same time until one long beep is heard.  
icon is displayed on the LCD screen, you  
Programming Mode has now been entered.  
Note: No action for five seconds will generate two long beeps indicating the  
Programming Mode has been exited.  
2. Within 5 seconds, press and hold the  
button until two beeping sounds are  
heard and the  
3. While the  
icon is displayed on the LCD screen indicating second car operation.  
is displayed, press any button on the transmitter to control the second vehicle’s  
security system or alarm function (arm/disarm/trunk/remote start).  
Note: Button functions are the same for the second car as they are for the first car.  
Return to First Car Operation (LCD Remote Only)  
1. Press and hold  
and  
buttons at the same time until one long beep is  
heard. Programming Mode has now been entered.  
Note: No action for five seconds will generate two long beeps indicating the  
Programming Mode has been exited.  
2. Within 5 seconds, press and hold the  
button until two beeping sounds are  
heard and the  
operation.  
icon is not displayed on the LCD screen indicating first car  
17  
 
Replacement Transmitters  
TRANSMITTERS  
DESCRIPTION  
MODEL #  
$ PRICE  
2-Way LCD Remote for  
the X9 Security System  
X4RF-LCD  
139.95 ea.  
4
4
SAVE  
1-Way Remote for  
the X9 Security System  
X7RF  
59.95 ea.  
Replacement Batteries  
REPLACEMENT BATTERIES  
1.5 Volt AAA Alkaline Battery commonly  
found in grocery stores, hardware stores,  
etc.  
CR2032 - 3 Volt Lithium Battery (1 pc.)  
Models:  
Radio Shack: #23-162  
Duracell: #DL2032  
Eveready: #ECR2032  
Panasonic: # CR2032  
18  
 
Replacement Parts Order Form  
Mail to: Magnadyne Corporation  
ATTN: Consumer Parts Sales  
P.O. Box 5365  
Credit Card or Money Order Only  
(Sorry No Cash, C.O.D. or personal checks accepted)  
Call: (310) 884-7777 Fax: (310) 637-9542  
Carson, CA 90749-5365  
SHIP TO: (No P.O. Boxes)  
LAST NAME  
FIRST NAME  
INITIAL  
STREET ADDRESS  
ADDITIONAL ADDRESS  
ADDITIONAL ADDRESS  
CITY  
STATE  
ZIP CODE  
DAY TIME PHONE NUMBER  
CREDIT CARD INFORMATION  
VISA  
MC  
CREDIT CARD N0.  
CARD HOLDER’S LAST NAME  
STREET ADDRESS  
CITY  
EXPIRATION DATE  
FIRST NAME  
INITIAL  
STATE  
QTY.  
ZIP CODE  
PART #  
DESCRIPTION  
PRICE EACH  
TOTAL  
Shipping and Handling  
Sales Subtotal = ________ . ______  
Up to $20.00  
20.01 to 30.00  
30.01 to 45.00  
45.01 to 70.00  
Over 70.01  
$5.00  
5.95  
6.50  
6.95  
7.95  
California Residents Add Sales Tax = ________ . ______  
Shipping and Handling (See Chart) = ________ . ______  
TOTAL = ________ . ______  
On regular orders please allow 4-5 weeks for delivery.  
Please give a shipping address where this order may be delivered between the hours of 9 am and 5 pm weekdays.  
If UPS is unable to deliver, your order will be returned and additional shipping charges will be required.  
19  
 
Limited Lifetime Warranty  
Magnadyne Corporation or its authorized agents will, for the life of the vehicle and to the original  
purchaser, repair, replace or refund the retail sales price of said product or any part thereof, at the  
option of the Magnadyne Corporation or its authorized agents, if said product or part is found  
defective in materials or workmanship, when properly connected and operating on the correct  
power requirements designated for the specific product. This warranty and Magnadyne Corporation  
or its authorized agents obligations, hereunder do not apply where the product was: damaged while  
in the possession of the consumer, subjected to unreasonable or unintended use, not reasonably  
maintained, utilized in commercial or industrial operation, or serviced by anyone other than  
Magnadyne Corporation or its authorized agent, or where the warning seal on the product is broken  
or the power plugs or wires are detached from the unit. Magnadyne Corporation or any of its  
authorized agents do not assume any labor costs for the removal and reinstallation of any product  
found to be defective, or the cost of transportation to Magnadyne Corporation or its authorized  
agents. Such costs are the sole responsibility of the purchaser.  
This warranty does not cover the cabinet, appearance items, normal wear and tear or accessories  
used in connection with the product resulting from improper installation, alteration, accident,  
misuse, abuse or acts of nature.  
This Limited Life Time Warranty applies only to the receiver section of the security system. Neither  
the siren, transmitters, wire harness or any accessory item added to or used with a Remote Mobile  
security system are covered by this Limited Life Time Warranty. Sirens, transmitters, wire harness  
or any accessory item are covered by our standard 12 month limited warranty.  
Magnadyne Corporation or its authorized agents shall not be liable to anyone for consequential  
or incidental damages or claims that may arise due to failure of product to operate properly  
except those accorded by law. Magnadyne's or its authorized agents liability to the repair,  
replacement of the product as stated above if all conditions of the warranty are met. No  
expressed warranty or implied warranty is given except those set forth herein. Magnadyne does  
not warrant or guarantee against break in damage or the theft of the vehicle in part or whole, or  
against the loss or damage to the contents of any vehicle in which a security system is installed.  
Magnadyne security systems are only a deterrent against possible theft.  
This warranty extends only to the original purchaser of the product and for the vehicle in which it  
was originally installed. This warranty is not transferable or assignable to any person or vehicle.  
Defective merchandise should be returned to the original point of purchase or secondly to  
Magnadyne Corporation, 1111 W. Victoria Street, Compton, CA 90220. A return authorization must  
be obtained before sending, or merchandise may be refused.  
X9-UM 07-23-08 Rev. A  
© Copyright 2008/ 2009 Magnadyne Corporation  
 

Lantronix Computer Hardware 900 581 User Manual
Lasko Electric Heater 5572 User Manual
Lenovo Computer Monitor L195 WIDE User Manual
Liebherr Freezer 7080 904 00 User Manual
LST Smoke Alarm FWI2 1 User Manual
Lux Products Thermostat TX500b User Manual
Marshall electronic Digital Photo Frame CV340 User Manual
Maytag Washer MGR8670W User Manual
Melissa Kitchen Grill 643 044 User Manual
Meridian America DVR DVP 2351 User Manual