Magnadyne Automobile Electronics MKE 100 User Manual

Transmitters  
Press Simultaneously to  
Turn On / Off Porch Light  
Locks All Doors  
(Including Cargo)  
Unlocks Entry  
Doors  
Locks All Doors  
(Including Cargo)  
Unlocks Entry  
Doors  
Turns On / Off  
Porch Light  
Locks All  
Cargo Doors  
Unlocks All  
Cargo Doors  
User's Manual  
Keypad Keyless  
Entry System  
Programming  
A. 3-Button Transmitter Programming  
(Does not apply to MKE-100)  
1. Turn the ignition switch to the "ON" position  
within 15 seconds.  
Note: This mode will only retain the last 4 remote  
transmitters programmed. If the transmitter mem-  
ory is exceeded, the security system will start  
deleting transmitters from memory in chronologi-  
cal order.  
2. Push the Program switch 5 times, the  
onboard LED will be flashing and the beeper will  
emit a long chirp to indicate the system is in  
Transmitter Programming mode.  
1. Turn the ignition switch to the "ON" position  
within 15 seconds.  
2. Push the Program switch 3 times, the  
onboard LED will be flashing and the beeper will  
emit a long chirp to indicate the system is in  
Transmitter Programming mode.  
3. Press and hold any button on the transmitter  
until the onboard LED turns on for 2 seconds  
and the beeper responds with a confirming  
chirp, indicating the signal has been stored into  
memory.  
4. If you have additional transmitters (up to 4)  
that need to be programmed, repeat step 3 for  
each transmitter.  
D. Programming the User Code  
(The default user code is "54321" )  
Note: This mode will only retain the last 4 "user  
codes" programmed. If the user code memory is  
exceeded, the security system will start deleting  
user codes from memory in chronological order.  
1. Enter the program code "12345" on the key-  
pad. The beeper will emit a long chirp to confirm  
the correct code was entered.  
2. Enter a new 4 to 6 digit user code on the key-  
pad. Do not use "1234".  
3. Finish by pressing the "LOCK" key on the key-  
pad. 1 long beep with 2 short beeps will confirm  
the new user code has been stored into memory.  
4. If you have additional user codes (up to 4)  
that need to be programmed, repeat steps 2-3  
for each new user code.  
Exit: Turn the ignition switch to the "OFF" posi-  
tion, or leave it for 15 seconds. The onboard  
LED turns off and the beeper will emit 3 long  
chirps to confirm exit.  
Models:  
MKE-100 / MKE-300 / MKE-400  
Exit: Press and hold the "LOCK" key for 1 sec-  
ond or if 15 seconds of inactivity occurs during  
the above steps, the unit will revert back to the  
last successfully stored code. 3 longs beeps  
confirm exit.  
B. 4-Button Transmitter Programming  
(Does not apply to MKE-100)  
Note: This mode will only retain the last 4 remote  
transmitters programmed. If the transmitter mem-  
ory is exceeded, the security system will start  
deleting transmitters from memory in chronologi-  
cal order.  
 

LevelOne Switch FSW 1610TX User Manual
Lok8u Computer Hardware K8SLI User Manual
LST Smoke Alarm 5451EIS User Manual
Mackie Car Speaker MR5S User Manual
Macsense Connectivity Network Router MIH 120 User Manual
Magnavox Portable CD Player MPC42017 User Manual
Makita Saw 5007NBA User Manual
Melissa Hair Dryer 635 068 User Manual
Memorex Stereo System MKS8590 User Manual
Metz Camcorder 34 AF 3M User Manual