Magnadyne Car Video System M3500DVD User Manual

Operation  
and Installation  
Manual  
Model: M3500DVD  
DVD/CD Receiver  
with AM/FM Tuner  
 
Location and Function of the Controls  
1. Equalizer/Loud Button (EQ): Press to select  
12. Multi-Function Button (4, INT):  
between the preset sound equalization settings.  
Press and hold the button to boost high and low  
tones at low volume levels (loudness).  
Radio: Recalls a memorized radio station,  
and programs a radio station into memory.  
CD: Press to activate the intro function which  
will play the beginning of every track for  
10 seconds.  
��  
2. Down ( l  
��  
) and Up (  
l ) Controls:  
Radio: Press and release to manually adjust the  
radio frequency down or up. Press and hold  
to automatically scan to the next radio station.  
13. Multi-Function Button (3, RDM):  
Radio: Recalls a memorized radio station,  
and programs a radio station into memory.  
DVD, CD, SD or USB: Press to randomly play  
tracks/chapters.  
DVD, CD, SD or USB: Changes tracks or  
chapters  
.
3. Mode Button (MODE): Press the MODE button to  
change the operating mode as follows: “AVIN F”  
Audio/Video In, Front > “AVIN R” Audio/Video In,  
Rear > “F1, F2, F3, AM1 or AM2” Radio > “LOAD”  
Music or Movie Disc > “USB” USB > “CARD” SD  
14. Multi-Function Button (2, A-B):  
Radio: Recalls a memorized radio sta-  
tion, and programs a radio station into  
memory.  
card*  
.
DVD, CD, SD or USB: Continuously repeats a  
selection of music/movie.  
*Available only when there is media inserted  
into Disc slot, USB slot or SD Card slot.  
15. Multi-Function Button (1, RPT):  
Radio: Recalls a memorized radio sta-  
tion, and programs a radio station into  
memory.  
4. Volume/Select Knob (VOL/SEL)  
Volume: Rotate VOL knob to adjust the volume  
level.  
Select: Press the VOL knob to enter the sound  
characteristics menu. Pressing the VOL  
knob will change the menu item as follows:  
“BAS” bass > “TRE” treble > “BAL” balance  
> “FAD” fader > “STEREO” stereo/mono FM  
reception > “BEEP OFF” beep confirmation  
for button press > “USA” radio frequency >  
“VOL” volume.  
DVD, CD, SD or USB: Press to repeat the cur-  
rent track/chapter. Press again to cancel the  
repeat function.  
16. Radio Band Button (BAND): Selects the desired  
radio band in the following order: F1, F2, F3,  
AM1 and AM2.  
17. IR Eye for Remote Control  
5. Automatic Memory Station (AMS): Press and hold  
for automatic station memory storing. Press and  
release for scanning memorizes stations.  
18. Play/Pause Button ( ll):  
DVD, CD, SD or USB: Press to pause the  
current track/chapter. Press again to  
resume play.  
6. Display Area: Displays: radio, disc, SD card and  
USB functions.  
19. Power/Mute Button (  
MUTE):  
7. USB Input: Plug in your USB device, “LOAD”  
then “USB” will appear in the display.  
Power: Press to turn the unit on when the  
unit is off, press and hold the button to  
turn the unit off.  
8. Face Plate Release Button (OPEN): Press to open  
face plate to allow access to disc slot, SD card  
slot and disc eject button.  
Mute: When the unit is on press and release  
this button to mute the audio, press again to  
restore the audio.  
9. 3.5mm Auxiliary Audio/Video Input Jack: Plug-in  
20. SD Card Slot: Insert a SD card with the notch  
a device with a 3.5mm audio/video input plug.  
in the card facing down, “LOAD” then “CARD”  
will appear in the display  
.
10. Multi-Function Button (6, +10):  
Radio: Recalls a memorized radio station,  
and programs a radio station into memory.  
DVD, CD, SD or USB: Press to skip up 10  
tracks/chapters.  
21. Eject Button ( ): Ejects the disc from the  
DVD/CD slot.  
22. Disc Slot: Insert a disc into the slot with label  
facing up.  
11. Multi-Function Button (5, -10):  
Radio: Recalls a memorized radio station,  
and programs a radio station into memory.  
DVD, CD, SD or USB: Press to skip down 10  
tracks/chapters.  
23. Reset Button: Press the RESET button if the  
unit freezes up or does not function correctly.  
3
 
Remote Control Button Locations and Functions  
Inserting the Batteries into the Remote Control:  
1. Open the battery compartment cover.  
2. Insert the new batteries. Make sure that the  
positive and negative terminals of the batteries  
are oriented as indicated.  
9. Display (DISP): Displays source information.  
10. Band: Selects F1, F2, F3, AM1 or AM2 radio  
bands.  
11. Equalizer/Loud (EQ): Press to select between  
the preset sound equalization settings.Press  
and hold the button to boost high and low  
tones at low volume levels (loudness).  
3. Close the cover.  
Using the Remote Control:  
Point the remote control towards the IR eye on  
the radio.  
12. Mute: Mutes the audio.  
Note: Operation angle is about 30 degree in each  
direction. Operation distance is about 15ft.  
13. Numeric Keypad: Inputs the corresponding  
number.  
14. Mode: Switches through the available sources.  
14  
15  
15. Menu: Displays the movie menu.  
16. Title: Displays the title menu that is stored on  
16  
17  
the movie disc.  
1
2
POWER  
MODE  
MENU  
TITLE  
�� ��  
,
to fast  
17. Disc Fast Rewind/Fast Forward (  
).  
��  
Press the fast forward button  
3
5
18  
4
forward disc play or press the fast reverse but-  
RANDOM  
ZOOM  
REPEAT  
ENTER  
EQ  
��  
ton  
to fast reverse disc play. Each time  
19  
6
7
VOL  
TONE  
the button is pressed, the speed changes. To  
SETUP  
20  
21  
resume normal play, press the play button ll.  
�� ��  
8
18. Tune/Track/Chapter (l  
,
l) :  
9
Radio: Press and release to manually adjust  
the radio frequency down or up. Press  
and hold to automatically scan to the next  
station.  
DISP  
BAND  
MUTE  
SLOW  
AUDIO  
22  
23  
10  
SUB.TT  
24  
11  
13  
12  
1
5
9
2
6
3
Disc: Press to change to a lower or higher  
track/chapter.  
4
8
7
+
19. VOL/TONE :  
Press to change the menu item as follows:  
“BAS” bass > “TRE” treble > “BAL” balance >  
“FAD” fader > “STEREO” stereo/mono FM recep-  
tion > “BEEP OFF” beep confirmation for button  
press > “USA” radio frequency > “VOL” volume.  
10/0 10  
1. Power On/Off: Turns the unit On or Off.  
2. Play/Pause ( ): DVD, CD, SD or USB: Press  
to pause the current track/chapter. Press again  
to resume play.  
20. SETUP:  
Access the Movie Disc Setup Menu, a movie  
disc has to be inserted.  
21. + ,  
-
(Volume Adjustment):  
Press to increase or decrease the volume level.  
They also adjust Bass, Treble, Balance and  
Fader when selected.  
3. Stop ( ): Stops disc play.  
4. Random: Press to randomly play tracks/chapters.  
5. Repeat: Repeats play of chapters, titles, tracks  
and discs.  
22. Slow: Press to play the movie disc in slow  
motion.  
23. Subtitle (SUB.TT): Accesses movie disc’s sub-  
6. Zoom: Enlarges or reduces the size of movie picture  
.
title languages.  
7. Cursor: (s, , t, ): Moves feature selec-  
24. Audio: Changes the language on multi-language  
tion up, down, left or right.  
movie discs.  
8. Enter: Confirms the selected item.  
4
 
General Operations  
Turning the Unit On:  
Press the  
unit is off.  
button to turn the unit On when the  
MODE  
EQ  
AMS  
MUTE  
AM/FM Multi-Media Receiver  
BAND  
Turning the Unit Off:  
SEL  
+
10  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
VOL  
6
Press and hold the  
button to turn the unit Off.  
Mode Selection:  
MODE  
Press the MODE button to change the operating  
mode as follows: “AVIN F” Audio/Video In, Front  
> “AVIN R” Audio/Video In, Rear > “F1, F2, F3,  
AM1 or AM2” Radio > “LOAD” Music or Movie  
EQ  
AMS  
MUTE  
AM/FM Multi-Media Receiver  
BAND  
SEL  
+
10  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
VOL  
6
Disc > “USB” USB > “CARD” SD card*  
.
*Available only when there is media inserted  
into Disc slot, USB slot or SD Card slot.  
Sound Controls  
Volume:  
Decrease  
Increase  
Increase the volume by rotating the knob clock-  
wise.  
MODE  
EQ  
AMS  
Decrease the volume by rotating the know counter-  
clockwise.  
MUTE  
AM/FM Multi-Media Receiver  
BAND  
SEL  
VOL  
+
10  
RPT  
A-B  
RDM  
INT  
4
10-  
5
1
2
3
6
Sound Characteristics Menu:  
By pressing the VOL knob, the modes will be dis-  
played in the following order: “BAS” bass, “TRE”  
treble, “BAL” balance and “FAD” fader.  
MODE  
EQ  
MUTE  
AM/FM Multi-Media Receiver  
BAND  
SEL  
+
10  
RPT  
1
A-B  
2
RDM  
INT  
4
10-  
5
VOL  
3
6
Balance:  
Bass:  
Press the VOL knob button until “BAL” appears  
in the display. Turn the VOL knob clockwise to  
increase the balance to the right and counter-  
clockwise to increase the balance to the left.  
Press the VOL knob until “BAS” appears in the  
display. Turn the VOL knob clockwise to increase  
the bass and counterclockwise to decrease the  
bass.  
Fader:  
Treble:  
Press the VOL knob button until “FAD” appears  
in the display. Turn the VOL knob clockwise to  
increase the balance to the front speakers and  
counterclockwise to increase the balance to the  
rear speakers.  
Press the VOL knob button until “TRE” appears  
in the display. Turn the VOL knob clockwise  
to increase the treble and counterclockwise to  
decrease the treble.  
Equalizer:  
The M3500DVD has pre-programmed audio set-  
tings. Press the EQ button to switch the equalizer  
settings. The equalizer setting will appear in the  
display: POP, ROCK, CLAS (classic) or off. The  
unit will leave equalizer programing after 5 sec-  
onds of no button activity.  
ODE  
EQ  
AMS  
MUTE  
AM/FM Multi-Media Receiver  
BAND  
SEL  
+
10  
RPT  
A-B  
RDM  
INT  
10-  
VOL  
1
2
3
4
5
6
5
 
Sound Controls (continued)  
Loudness:  
Hold  
To boost high and low tones at low volume lev-  
els, press and hold the EQ button until “LOUD”  
appears in the display. To deselect, press and  
hold the EQ button again until “LOUD” disap-  
pears from the display.  
ODE  
EQ  
AMS  
MUTE  
AM/FM Multi-Media Receiver  
BAND  
SEL  
+
10  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
VOL  
6
Mute:  
MODE  
Press the  
MUTE button to cutoff the audio.  
EQ  
AMS  
Press it again to restore the audio.  
MUTE  
AM/FM Multi-Media Receiver  
BAND  
SEL  
+
10  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
VOL  
6
Radio Operation  
Selecting a Band:  
1. Press the MODE button until either “F1, F2,  
F3”, AM1 or AM2” appears in the display.  
MODE  
MODE  
MODE  
EQ  
AMS  
MUTE  
AM/FM Multi-Media Receiver  
BAND  
SEL  
+
10  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
VOL  
VOL  
6
2. Next press the BAND button to select the  
desired band: “F1, F2, F3” (FM) or “AM1,  
AM2” (AM).  
EQ  
AMS  
MUTE  
AM/FM Multi-Media Receiver  
BAND  
SEL  
+
10  
RP
1
A-B  
2
RDM  
3
INT  
4
10-  
5
6
Manual Tuning:  
��  
��  
Press and release the  
l or l  
button until  
EQ  
AMS  
desired frequency is selected.  
MUTE  
Automatic Search Tuning:  
Press and hold the  
AM/FM Multi-Media Receiver  
D  
SE
+
10  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
��  
��  
l or l  
button to  
6
move to the next or previous station automati-  
cally. Then release and press and hold the but-  
ton again to scan to the next radio station.  
Down  
Up  
Preset Radio Stations:  
The six numbered preset buttons can store and recall  
stations for each band (F1, F2, F3, AM1 or AM2).  
Radio Band  
Preset Number  
MODE  
EQ  
AMS  
Memorizing a Station:  
1. Select a radio band.  
MUTE  
2. Tune in a radio station.  
AM/FM Multi-Media Receiver  
BAND  
SEL  
VOL  
+
10  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
3. Press and hold any of the preset buttons for  
three seconds to memorize the station. The  
preset number will appear in the display.  
6
Radio Station  
Recalling a Station:  
1. Select a band (F1, F2, F3, AM1 or AM2)  
.
2. Press one of the six preset buttons to select  
a stored station.  
6
 
Radio Operation (continued)  
Preset Radio Stations (continue)  
Automatically Memorizing Station:  
1. Select a band (AM or FM).  
MODE  
EQ  
AMS  
MUTE  
2. Press and hold the AMS button for two sec-  
onds. The radio automatically selects strong  
stations and stores them in each preset  
number for the selected radio band. The  
new stations replace stations already stored  
in that band.  
AM/FM Multi-Media Receiver  
BAND  
SEL  
+
10  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
VOL  
6
3. After the new stations are stored into memory,  
the tuner will start playing the memorized stations  
each for 5 seconds. When a desired station is  
reached, press the AMS button to stop scanning.  
Scanning Memorized Stations:  
To scan preset stations stored in the current  
band press and release the AMS button. The  
radio pauses for five seconds at each preset  
station. When the desired station is reached,  
press the AMS button again to stop scanning.  
FM Stereo/Mono Reception:  
For weaker FM stereo stations selecting mono  
reception usually improves reception. To switch  
from stereo to mono reception press the VOL knob  
until “STEREO” appears in the display. Rotate the  
VOL knob until “MONO” appears in the display.  
The unit will leave feature programing after 5 sec-  
onds of no button activity.  
MODE  
EQ  
MS  
MUTE  
AM/FM Multi-Media Receiver  
BAND  
SEL  
+
10  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
VOL  
6
CD (Music) Disc, SD Card and USB Drive Operation  
Loading a CD:  
1. Press the OPEN button to flip down the face  
and to allow access to the disc slot.  
OPEN  
MODE  
AMS  
2. Insert a CD into the disc slot with the label side  
up. Inserting the disc will automatically switch  
the unit to the “CD” mode.  
AM/FM Multi-Media Receiver  
USB  
BAND  
+
10  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
AUX  
6
3. Close the unit’s face.  
Label Side Up  
Ejecting a CD:  
1. Press the OPEN button to flip down the face  
and to allow access to the disc slot.  
2. Press the button to eject the disc from the  
unit. Remove the disc.  
3. Close the radio face.  
7
 
CD (Music) Disc, SD Card and USB Drive Operation (continued)  
Inserting the USB Drive:  
1. Flip open the door to allow access to the USB slot.  
OPEN  
AMS  
2. Gently insert the USB drive into the slot.  
Inserting the USB drive will automatically  
AM/FM Multi-Media Receiver  
UB  
BAND  
+
10  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
switch the unit to the “USB” mode.  
AUX  
6
Note: If a drive does not insert, DO NOT FORCE  
it into the slot, flip the drive over and try again  
.
Removing the USB Drive:  
Remove a USB drive at any time by pulling the  
device out of the socket.  
Inserting the SD Card:  
1. Press the OPEN button to flip down the face  
and to allow access to the SD slot.  
OPEN  
MODE  
AMS  
2. Gently insert the SD card into the slot with the  
angle key in the card facing down until it clicks  
into place. Inserting the SD card will automati-  
cally switch the unit to the SD “CARD” mode.  
Note: If a card does not insert, DO NOT FORCE  
it into the slot, flip the card over and try again.  
3. Close the unit’s face.  
AM/FM Multi-Media Receiver  
USB  
BAND  
+
10  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
AUX  
6
Removing the SD Card:  
1. Press the OPEN button to flip down the face  
and to allow access to the SD slot.  
2. Push in on the SD card until you hear a click,  
then release the SD card and remove it.  
3. Close the unit’s face.  
Select Tracks:  
Track Number  
��  
��  
Press and release either the  
l or l  
button  
MODE  
EQ  
for less than a second to move to the next or  
previous track. The track number appears in the  
display area.  
AMS  
MUTE  
AM/FM Multi-Media Receiver  
D  
SE
+
10  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
6
Pause Play:  
MODE  
EQ  
Press the ll button to pause play. Press it again  
AMS  
to resume play.  
MUTE  
AM/FM Multi-Media Receiver  
BAND  
SEL  
+
10  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
VO
6
CD Repeat Function:  
The default setting is to repeat the entire disc. Press  
the 1/RPT button to change the repeat function:  
“REPEAT OFF” = Disc will stop playing at end  
of disc.  
MODE  
EQ  
AMS  
MUTE  
AM/FM Multi-Media Receiver  
BAND  
SEL  
+
10  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
VOL  
6
“REPEAT 1”  
= The track playing will  
continuously repeat.  
“REPEAT ALL” = The entire disc repeats  
continuously.  
8
 
CD (Music) Disc, SD Card and USB Drive Operation (continued)  
Disc, USB or SD Card Repeat Function:  
MODE  
EQ  
The default setting is repeat is off. Press the  
AMS  
1/RPT button to change the repeat function:  
MUTE  
“REPEAT 1”  
= The track playing will  
continuously repeat.  
AM/FM Multi-Media Receiver  
+
BAND  
SEL  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
10  
6
VOL  
“REPEAT DIR” = The entire directory will  
continuously repeat.  
“REPEAT ALL” = All the tracks will  
continuously repeat.  
“REPEAT OFF” = Will stop playing at end  
of last track.  
Play All Tracks in Random Order:  
Press the 3/RDM button to play all tracks in random  
order. Press it again to stop playing in random order.  
MODE  
EQ  
AMS  
MUTE  
AM/FM Multi-Media Receiver  
BAND  
SEL  
+
10  
RPT  
1
A-B  
RDM  
3
INT  
4
10-  
5
VOL  
6
CD Intro Scan:  
MODE  
Press the 4/INT button to play the first ten sec-  
onds of each track. Press it again to stop intro  
scan and listen to the track.  
EQ  
AMS  
MUTE  
AM/FM Multi-Media Receiver  
BAND  
SEL  
+
10  
RPT  
1
A-B  
2
RDM  
INT  
4
10-  
5
VOL  
6
Track Skip Buttons:  
Press the 5/-10 button to skip down 10 tracks.  
Press the 6/+10 button to skip up 10 tracks.  
MODE  
EQ  
AMS  
MUTE  
AM/FM Multi-Media Receiver  
BAND  
SEL  
+
10  
RPT  
1
A-B  
2
RDM  
3
INT  
10-  
5
VOL  
6
Auxiliary Audio/Video Input  
Front Audio/Video Input Jack:  
OPEN  
1. Connect an audio/video device using a 3.5mm  
jack (not supplied) into the socket mounted on  
the front of the unit.  
2. Press the MODE button until “AVIN F” appears  
in the display.  
AMS  
AM/FM Multi-Media Receiver  
USB  
BAND  
+
10  
RPT  
1
A-B  
RDM  
3
INT  
4
10-  
5
AUX  
2
6
Note: The unit will not control the auxiliary source,  
but can adjust the sound controls. Refer to the  
audio/video device’s owners manual for proper  
operation.  
MODE  
EQ  
AMS  
MUTE  
Rear Audio/Video Input:  
1. An auxiliary audio/video device must be con-  
nected to the rear of the unit.  
AM/FM Multi-Media Receiver  
BAND  
SEL  
+
10  
RPT  
1
A-B  
RDM  
3
INT  
4
10-  
5
VOL  
2
6
2. Press the MODE button until “AVIN R” appears  
in the display.  
9
 
DVD (Movie) Disc Operation  
Loading a DVD:  
OPEN  
MODE  
1. Press the OPEN button to flip down the face  
and to allow access to the disc slot.  
AMS  
2. Insert a DVD into the disc slot, label side up,  
and the DVD will begin to play.  
AM/FM Multi-Media Receiver  
USB  
BAND  
+
10  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
AUX  
6
3. Close the unit’s face.  
Label Side Up  
Ejecting a DVD:  
1. Press the OPEN button to flip down the face  
and to allow access to the disc slot.  
2. Press the  
button to eject the disc from the  
unit. Remove the disc.  
3. Close the radio face.  
Menu Screen:  
1. Press the MENU button on the remote to  
access the menu screen of the movie disc.  
POWER  
MODE  
REPEAT  
MENU  
TITLE  
2. Use the s, , t, buttons on the remote  
to navigate to the menu item you want.  
3. Press the ENTER button to execute your  
selected menu item.  
RANDOM  
Pausing/Playing a Movie Disc:  
MODE  
EQ  
Press the ll button to pause the movie disc.  
AMS  
“PAUSE” will appear in the display.  
MUTE  
AM/FM Multi-Media Receiver  
+
BAND  
SEL  
To resume playing the disc, press the ll button.  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
10  
6
VO
Stopping a Movie Disc:  
Press the button on the remote control to  
POWER  
RANDOM  
MODE  
MENU  
TITLE  
stop play. To resume play, press the ll button.  
Press the button 2 times, then press the ll  
button and the movie disc will start playing from  
the beginning.  
REPEAT  
Selecting a Chapter:  
Chapter Number  
��  
Press and release the l  
previous chapter.  
button to select a  
MODE  
EQ  
AMS  
��  
Press and release the  
next chapter.  
l button to select a  
MUTE  
AM/FM Multi-Media Receiver  
ND  
SEL  
+
10  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
6
10  
 
DVD (Movie) Disc Operation (continued)  
ENTER  
Subtitle Language Menu:  
P
ress the SUB.TT button on the remote during  
DISP  
BAND  
MUTE  
SLOW  
AUDIO  
playback. Each time the button is pressed, the  
subtitle language changes. The selection of sub-  
title appears at the top of the screen.  
EQ  
SUB.TT  
Notes:  
1
2
3
1. Some discs may contain only one subtitle  
language.  
2. Depending on the disc, the number of subtitle  
languages may be different.  
Zoom Selection:  
RANDOM  
ZOOM  
REPEAT  
ENTER  
1. Press the ZOOM button on the remote to  
VOL  
TONE  
enlarge the on-screen image during disc play.  
Each time the ZOOM button is pressed, the  
magnification increment changes in the fol-  
lowing order: 2X, 3X, 4X, 1/2, 1/3, 1/4.  
SETUP  
SLOW  
DISP  
2. Use the navigation buttons s, , t, on  
the remote to move the image on the screen.  
VOL  
TONE  
ZOOM  
SETUP  
On Screen Display Selection:  
P
ress the DISP button on the remote during  
ENTER  
movie play to display the following information in  
this order for most discs:  
DISP  
SLOW  
AUDIO  
Title Elapse, Title Remain, Chapter Elapse,  
Chapter Remain and Display Off.  
BAND  
EQ  
SUB.TT  
Fast Forwarding / Fast Rewinding:  
��  
��  
Press the  
or  
button on the remote  
to start the fast forward or fast rewind function  
speed of 2 times normal speed (X 2). “FORWARD  
X 2 or BACKWARD X 2” will appear in the display.  
POWER  
MODE  
REPEAT  
MENU  
TITLE  
��  
��  
Press and hold the  
or  
button again will  
RANDOM  
ZOOM  
increase the speed, X 4, X 8 and X 20. Press the  
ll button to resume normal movie disc playback.  
VOL  
TONE  
SETUP  
Slow Motion:  
Continue to press the SLOW button on the remote  
to play the movie is slow motion in the following  
order:  
ENTER  
DISP  
SLOW  
AUDIO  
SF 1/2, SF 1/3, SF 1/4, SF 1/5, SF 1/6, SF 1/7  
BAND  
EQ  
SUB.TT  
To resume normal play, press the ll button.  
ENTER  
Audio Language:  
P
ress the AUDIO button on the remote during  
DISP  
BAND  
MUTE  
SLOW  
AUDIO  
playback to select the desired audio/language  
setup. The audio languages will appear at the top  
of the screen.  
EQ  
SUB.TT  
1
2
3
11  
 
DVD (Movie) Disc Operation (continued)  
Title Screen:  
P
ress the TITLE button on the remote, depend-  
POWER  
RANDOM  
MODE  
REPEAT  
MENU  
TITLE  
ing on the characteristics of the movie disc  
the title function may be invalid. This is not a  
malfunction.  
Direct Chapter Selection:  
1. Using the numeric keypad on the remote con-  
trol enter the chapter number.  
MUTE  
4
1
5
9
2
6
3
7
2. Press the ENTER button to confirm.  
+
8
10/0 10  
Last Play Memory:  
During disc play, if you turn off the unit and  
turn it on again, the movie will resume playing  
from where it was stopped  
.
During disc play, if you press the MODE but-  
ton to switch to another mode, and return to  
the movie mode again, the unit will resume  
playing from where it was stopped.  
12  
 
DVD (Movie) Disc Operation (continued)  
Screen Adjustment Controls:  
RANDOM  
ZOOM  
REPEAT  
ENTER  
1. Press the SETUP button on the remote to  
enter the setup menu.  
OL  
TONE  
SETUP  
2. When the cursor is on the top of the screen  
use or button to select different pages,  
such as: SYSTEM SETUP, LANGUAGE  
SETUP, VIDEO SETUP, SPEAKER SETUP and  
DIGITAL SETUP.  
3
4
. Press t button to move the cursor to SETUP  
page below and use s and t buttons to  
move among the different SETUP options.  
VOL  
TONE  
ZOOM  
SETUP  
SLOW  
ENTER  
. Press button to display the list of choices  
for each SETUP menu item. Use s and t to  
DISP  
change selection.  
5. Press ENTER button to confirm your selection.  
SYSTEM SETUP  
TV SYSTEM  
AUTO PLAY  
TV TYPE  
PASSWORD  
RATING  
LANGUAGE SETUP  
OSD LANGUAGE  
AUDIO LANG  
SUBTITLE LAN  
MENU LANG  
DEFAULT  
- TV SYSTEM: NTSC, PAL or AUTO  
- AUTO PLAY: On or Off  
- TV TYPE: 4:3 PS, 4:3LB or 16:9  
- PASSWORD: Lock/unlock (default 0000)  
- RATING: 1KID SAFE, 2G, 3PG, 4PG13, 5PG-  
R, 6R, 7NC17 or 8ADULT.  
- DEFAULT: Restore the SYSTEM SETUP  
menu.  
- OSD LANGUAGE: English, German, Spanish,  
French and Portuguese.  
- AUDIO LANGUAGE: Chinese, English,  
Japan, French, Spanish, Portuguese, Latin  
and German.  
- SUBTITLE LANGUAGE: Chinese, English,  
Japan, French, Spanish, German and Off.  
- MENU LANGUAGE: Chinese, English, Japan,  
French, Spanish, Portuguese, German and  
Latin.  
VIDEO SETUP  
BRIGHTNESS  
CONTRAST  
HUE  
SPEAKER SETUP  
DOWNMIX  
FRONT  
SATURATION  
SHARPNESS  
You can adjust the value of brightness, con-  
trast, hue, saturation and sharpness.  
- DOWNMIX: LT/RT, STEREO or VSS  
- FRONT: Large or Small  
13  
 
Wiring Diagram  
White/Black Wire  
Gray/Black Wire  
Gray Wire  
Left  
Front  
Speaker  
Right  
Front  
Speaker  
White Wire  
Audio Output Right (Red)  
Audio Output Left (White)  
Video Output (Yellow)  
Video Input (Yellow)  
Audio Input Left (White)  
Audio Input Right (Red)  
External Antenna  
Violet/Black Wire  
Violet Wire  
Left  
Rear  
Speaker  
Green/Black Wire  
Green Wire  
Right  
Rear  
Speaker  
Red Wire (+) to 12 Volt Ignition  
Black Wire Ground  
Yellow Wire (+) to 12 Volt Constant  
Blue Wire Power Antenna (12V Out)  
14  
 
Installation Procedures  
Mounting Sleeve  
Sheet Metal  
Screw  
Nut  
Washer  
Push Out Mounting  
Sleeve Tabs  
Metal Strap  
Dashboard  
Removal Keys  
Installing the Unit:  
1: Insert the sleeve into the dashboard opening and  
Removing the Unit:  
1: Remove the trim ring.  
bend the mounting tabs outward to secure it.  
2: Insert the release keys into the left and right  
2: If necessary, attach the mounting strap to the rear  
side of the unit.  
of the unit, then attach it with the supplied nut.  
3: Pull the unit out of the dashboard.  
3: Insert the unit into the sleeve until you hear a click.  
4: Finally place the trim ring over the unit.  
15  
 
Reset Function  
Press the OPEN button on the front panel to fold  
down the panel, and you will see the RESET but-  
ton on the base of the unit.  
When the below situation occurs, you can press  
the RESET button to solve the problem:  
• Initial installation of the unit when all wiring  
is completed.  
• Some of the buttons do not work.  
• Error symbol on the display.  
Should any of these conditions occur, simply  
press and release the restart button using the tip  
of a ball point pen. This will restart the radio’s  
microprocessor. After pressing the restart but-  
ton, you should recheck to see if the radio func-  
tions normally.  
Additional Features  
Button Press Beep Confirmation:  
If you want the M3500DVD to beep everytime a  
button is pressed follow the instructions below:  
MODE  
EQ  
MS  
MUTE  
AM/FM Multi-Media Receiver  
1. Press the VOL knob until “BEEP OFF” appears  
in the display.  
BAND  
SEL  
+
10  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
VOL  
6
2. Rotate the VOL knob until “BEEP ON” appears  
in the display  
.
3. After waiting a few seconds the unit will exit  
programming.  
Area Radio Frequency Adjustment:  
Note: If operating the unit in the USA do not  
change the area.  
MODE  
EQ  
MS  
MUTE  
To Change the Area:  
AM/FM Multi-Media Receiver  
BAND  
SEL  
+
10  
RPT  
1
A-B  
2
RDM  
3
INT  
4
10-  
5
VOL  
6
1. Press the VOL knob until “USA” appears in the  
display.  
2. Rotate the VOL knob until “OCEAN” appears in  
the display  
.
3. After waiting a few seconds the unit will exit  
programming.  
16  
 
Troubleshooting  
The disc can not play:  
If it appears that your unit does not operate prop-  
erly, first consult this checklist. It may be some-  
thing simple which has been overlooked.  
• Disc is of poor quality or damaged or not clean.  
Clean or replace the disc with one of higher  
quality.  
• The disc installed is not supported by the unit.  
Examine the disc type.  
Under no circumstances should you try to repair  
the player yourself, as this will invalidate the  
warranty. Only qualified service personnel can  
remove the cover or service this player.  
Disc can not be loaded or ejected:  
The power does not turn on:  
Hold the  
button for 5 seconds to reset the  
mechanism. Turn off the unit, and turn on the  
unit again.  
• The lead wires are not connected properly to  
the connectors. Make sure the connection is  
correct.  
The desired source is not selected although you  
press the MODE button:  
• An optional unit required to listen to each  
source is not connected yet. Connect the  
optional unit correctly.  
• One of the fuses has blown. After checking for  
short circuits in the wires, replace the fuse  
with one having the same rating.  
• The internal processor is not working due to  
noise or other factors. Press the reset button to  
reset the unit to factory defaults.  
• The reset button is not pressed yet although the  
optional unit has been connected to the unit.  
Press the RESET button.  
The remote control does not work. The unit does  
not operate even when the correct buttons on the  
remote control are pressed:  
• Battery capacity is low. Install new batteries.  
• Some operations are disabled in specific  
modes. Enter the correct mode.  
Replaceable Fuses  
If the fuse should blow, check that the wiring is  
correct. If the wiring is correct, replace the fuse  
with the same amperage rating as the original.  
Yellow Wire = 15 Amp glass fuse.  
Red Wire = 1 Amp glass fuse.  
17  
 
Disc Warnings  
Handling:  
• Dirt, dust, scratches and warping disc will cause  
non-operation.  
Label side up  
Do not place stickers on disc or scratch disc.  
• Do not place discs in the following places: Direct  
sunlight, dirty, dusty or damp areas, near car  
heaters, car seats or dashboard.  
Do not touch  
the underside  
of the disc  
Disc Cleaning:  
Use a dry, soft cloth to wipe the disc’s surface. If the  
disc is very dirty, use a soft cloth slightly moistened  
with isopropyl (rubbing) alcohol. Never use solvents  
such as benzine, thinner or conventional record  
cleaners as they may mar the surface of the disc.  
Do not bend  
Wipe the disc from  
the center toward  
the outside edge  
Note: A disc may become somewhat scratched  
(although not enough to make it unusable)  
depending on handling and conditions in the usage  
environment.  
Preparing New Discs with Rough Spots:  
A new disc may have rough edges on its inside  
and outside edges. If a disc with rough edges is  
used, the proper setting will not be performed and  
the player will not play the disc. Therefore, remove  
the rough edges in advance by using a ball point  
pen or pencil as shown. To do this, press the side  
of the pen or pencil against the inside and outside  
edges of the disc.  
Rough spots on  
outside edge  
Rough spots on  
inside edge  
Ball point pen  
or pencil  
18  
 
Warranty  
ONE (1) YEAR LIMITED WARRANTY  
Magnadyne Corporation or its authorized agents will within one year from the date of sale  
to you, repair, replace or refund the retail sales price of said product or any part thereof, at  
the option of the Magnadyne Corporation or its authorized agents, if said product or part  
is found defective in materials or workmanship, when properly connected and operating  
on the correct power requirements designated for the specific product. This warranty and  
Magnadyne Corporation or its authorized agent’s obligations hereunder do not apply where  
the product was; damaged while in the possession of the consumer, subjected to unrea-  
sonable or unintended use, not reasonably maintained, utilized in commercial or industrial  
operations, or serviced by anyone other than Magnadyne Corporation or its authorized  
agents, or where the warning seal on the product is broken or the power and/or plugs  
are detached from the unit. Magnadyne Corporation or any of its authorized agents will  
not assume any labor costs for the removal and reinstallation of any product found to be  
defective, or the cost of transportation to Magnadyne Corporation or its authorized agents.  
Such cost are the sole responsibility of the purchaser.  
This warranty does not cover the cabinet appearance items or accessories used in con-  
nection with this product, or any damage to recording or recording tape, or any damage  
to the products resulting from improper installation, alteration, accident, misuse, abuse or  
acts of nature.  
MAGNADYNE CORPORATION OR ITS AUTHORIZED AGENTS SHALL NOT BE LIABLE TO  
ANYONE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR CLAIMS EXCEPT THOSE  
ACCORDED BY LAW. NO EXPRESSED WARRANTY OR IMPLIED WARRANTY IS GIVEN  
EXCEPT THOSE SET FORTH HEREIN. NO IMPLIED WARRANTY SHALL EXTEND BEYOND  
ONE YEAR FROM THE DATE OF SALE.  
This warranty extends only to the original purchaser of the product and is not  
transferable. Some states do not allow limitations on how long an implied warranty lasts,  
and some states do not allow the exclusion or limitation of incidental or consequential  
damages, so the above limitations or exclusion may not apply to you. This warranty gives  
you specific legal rights, and you may have other rights that vary from state to state.  
“NOTE: The manufacturer is not responsible for any radio or TV interference caused by  
unauthorized modifications to this equipment. Such modifications could void the User’s  
authority to operate the equipment.”  
Defective merchandise should be returned to the original point of purchase or  
secondly, to Magnadyne Corporation, 1111 W. Victoria Street, Compton CA 90220.  
Return Authorization must be obtained before sending, or merchandise may be refused.  
19  
 
© Copyright 2012  
Magnadyne Corporation  
M3500DVD-UM  
Rev. A 5-14-12  
 

Learning Resources Marine GPS System LER 3240 User Manual
LG Electronics Double Oven LDG3011ST User Manual
LG Electronics Flat Panel Television RU 17LZ20 RU 17LZ21 RU 17LZ22 User Manual
Lifebreath Thermostat 40DHWDFT User Manual
Lincoln Automobile 2008 MKZ User Manual
Magnavox Flat Panel Television 15MF237S User Manual
Manhattan Computer Products Computer Drive 451109 User Manual
McCulloch Blower MCB2203 User Manual
McCulloch Lawn Mower 14596 User Manual
Memorex CRT Television MT1132 User Manual