INSTALLATION
NNPackage Contents
Single Line Telephone
AT-1 0
USER'S GUIDE
Wall-mount screws
(2 pieces)
Telephone Set
User's Guide
LOCATION OF CONTROLS
NNInstalling the Telephone
1. Fit the other end of telephone line cord to your telephone network outlet.
Message Waiting Lamp
NNSelecting Dial Mode
Set the Dial Mode Switch either to DP(Pulse) or MF(Tone) according to the telephone
network. For installation on a PBX, check with your supplier for the correct dialing mode.
NNWall-Mounting
To wall-mount the phone:
1. Mark off the correct positions for the screws (included), 83.5mm apart vertically
opposed before drilling the wall.
PROGRAM Key
2. Install the screw into the wooden wall.
3. Mount the telephone on the wall so that the screw head inserts into the concave on
bottom of the telephone.
FLASH Key
REDIAL Key
Dial Keys
Receiver Volume Controls
Screw
83.5mm
Handset Holder
LINE Jack
Wall Mount Concave
To store the handset without hanging up:
HANDSET Jack
1. Hang the handset on the handset holder.
Dial Mode Switch
MM6017-1010
FEATURES
CARE AND MAINTENANCE
NNMaking a Call
1. Lift handset.
2. Hear dial tone.
3. Dial number.
NNAnswering a Call
1. Lift handset when the phone rings.
1. Avoid installing the phone where there is direct sunlight, or near heating appliances,
since this may cause discoloration and warping.
2. When the telephone becomes dirty, wet a soft cloth with diluted neutral detergent,
wring it out and wipe. Do not use strong cleaning agent or abrasive powder.
3. Keep away from TV sets, radios, etc. which may generate electrical noise.
4. Avoid dropping the handset and other rough treatment.
NNLast Number Redial
1. Lift handset.
Warning:
2. Press
key to redial your last call (up to 31 digits).
The handset receiver may retain dangerous materials such as metallic pins and staples
because the receiver induces magnet.
NRedial after flashing is not available.
NNFlash
While on a call, press
CHECKLIST FOR TROUBLESHOOTING
key for outside line or PBX features.
NDoes the hookswitch pop up ?
NNPulse to Tone Switching
When placing a call in DP (Pulse) mode, you can dial
NIs the dial mode switch (DP/MF) set to the correct position ?
NAre phone line cord and handset cord securely plugged in ?
If you disconnect the phone from the network, the data in phone's memory such
as redial number and ringing tone assignment will be erased (back to default) in a
few hours.
to change to MF (Tone)
dialing. The dial mode automatically reverts to DP mode when you hang up.
NNAdjusting Receiver Volume
1. Press keys to increase/decrease handset receiver volume while on a call.
NFor other problems, contact your supplier.
NVolume can be increased 3 levels, decreased 2 levels against the default level.
NNSelecting Ringing Pitch and Ringing Volume
1. Lift handset.
2. Press
3. Dial
4. Dial
key.
Ringing Volume
.
Soft Medium Loud
Slow
Medium
Fast
1
4
7
2
5
8
0
3
6
9
Ringing
Tone
Pitch
—
(Refer to the table in the right).
5. Press key.
6. Hang up.
Off
(Default: 6)
Nothing contained in this manual shall be deemed to be, and this manual does not constitute, a warranty of,
or representation with respect to, any of the equipment covered. This manual is subject to change without
notice and NEC has no obligation to provide any updates or corrections to this manual.
NIf you lift handset after setting to "0"(Off), the ringing tone automatically reverts to
the previous value.
NNMessage Waiting Lamp
Message Waiting Lamp lights when you have messages waiting (if your PBX system can
send them). Also flashes when your telephone rings.
Tokyo, Japan
|