Nady Systems Noise Reduction Machine PCL815 User Manual

PULL  
PULL  
REAR OUTLETS  
RACK LIGHTS  
DIMMER  
ON  
STANDARD  
VOLTAGE  
OVER  
VOLTAGE  
MIN  
MAX  
OFF  
POWER CONDITIONER & LIGHT MODULE  
1800 WATTS CAPACITY  
 
3
 
Controls, functions, and connections  
FRO N T PAN EL  
PULL  
PULL  
REAR OUTLETS  
RACK LIGHTS  
DIMMER  
ON  
STANDARD  
VOLTAGE  
OVER  
VOLTAGE  
MIN  
MAX  
OFF  
POWER CONDITIONER & LIGHT MODULE  
1800 WATTS CAPACITY  
1
6
2
3
5
6
4
2
1. POWER SWITCH  
Outlet switch (with built-in LED ON indicator) activates protection and filtration to all back panel outlets. To turn  
the unit ON or OFF, press the upper or lower portion of this button.  
2. 2 RETRACTABLE RACK LIGHTS  
Pull out for illumination and swivel to desired angle  
3. LIGHT SWITCH  
Activates rack illumination  
4. DIMMER CONTROL  
Use to control the intensity of the illumination. Turning clockwise increases the light output.  
5. DIGITAL VOLTMETER READOUT  
Displays incoming AC line voltage  
6. VOLTAGE LED METER  
Separate green and red LEDs monitor the incoming voltage range. The green LED indicates voltage is in the  
normal operating range. The red LED lights when the voltage exceeds 125V, indicating that the supplied power  
is out of range for normal operation.  
4
 
REAR PAN EL  
8
9
7
7. POWER CORD  
Heavy duty 14-guage power cord for connection to the AC power mains (~115V/ 60Hz)  
8. CIRCUIT BREAKER  
Resettable 15 amp thermal circuit breaker  
9. 8 REAR PANEL OUTLETS  
EMI/ RFI filtered, spike/ surge protected and switched  
5
 
Installation and operation  
1. The PCL Series conditioners are the perfect accessories for any rack mount system. Install in the top slot of a  
standard 19-inch rack, and the 8 switched AC outlets on the rear panel will provide full safety protection to all  
your rack equipment. These conditioners protect your delicate electronic equipment by combining a high  
voltage varistor surge and transient suppressor with an RFI/ EMI interference filter. The filter helps prevent noise  
from fluorescent lights, motors, and similar sources of “electronic pollution” from contaminating the AC feed to  
your senitive video, audio, vtr or computer circuits.  
2. Plug Power Cord (7) into a standard grounded 115V outlet  
3. Plug sensitive electronic equipment into the 8 Rear Panel Outlets (9)  
4. Turn Outlet Power Switch (1) to “ON” position. Lit LED indicates conditioned power to the connected  
equipment.  
5. For discreet illumination of your rack equipment on stage, in studios, and in other dark locations (PCL-  
810/ 815 only), pull the 2 Retractable Rack Lights (2) out and adjust the Dimmer Control (4) for the lamp  
brightness desired (see fig.1 below). The lights swivel and can be adjusted to the proper angle for your appli-  
cation. The lamps are supplied with standard 5W night-light bulbs. If you find the heat from the bulbs exces-  
sive, reduce the setting of the Dimmer Control or substitute lesser wattage bulbs. You can easily replace the  
bulbs without removing the unit from the rack by unscrewing the cap on the end of each light tube. (Note: Be  
careful not to push the tubes in while the caps are unscrewed.)  
6. The Digital Voltmeter Readout (5) (PCL-815 only) is calibrated to a nominal 117 VAC at the factory.  
No adjustments are necessary.  
7. The Digital Voltmeter Readout (5) automatically displays incoming voltage when the Power Cord (7)  
is connected.  
8. MAXIMUM LOAD: The PCL Series Power Conditioners 8 Rear Panel Outlets are rated at 15 amps total load  
(or 1800W at 120VAC). If this maximum load is exceeded, the Circuit Breaker (8) will trip, cutting off power  
to all connected equipment in your rack. If this happens, reduce the load by unplugging one or more units  
from the power conditioner, and push the circuit breaker to reset it (see fig.2 below).  
fig.2  
fig.1  
6
 
Specifications  
PROTECTION PROVIDED  
High voltage varistor surge and transient suppressor,  
RFI/ EMI interference filtration  
8 standard 3-prong grounded AC receptacles  
Maximum 1800W/ 15A load  
~120VAC/ 60 Hz  
OUTLET CONNECTORS  
POWER CONSUMPTION  
POWER SOURCE  
CIRCUIT BREAKER  
15A thermal type  
LAMPS (PCL-810/ 815)  
DIMENSIONS  
5W (two)  
19” X 1.75” X 7.3”  
(483 X 44 X 185mm), 1U rack height  
WEIGHT  
PCL-800 4.45 lbs (2.0 Kg)  
PCL-810 4.5 lbs (2.05 Kg)  
PCL-815 4.55 lbs (2.07 Kg)  
For improvement purposes, specifications, design and appearance subject to change without prior notice  
7
 
 

Miele Clothes Dryer T 4423 C User Manual
Milwaukee Electric Heater 2321 20 User Manual
Nikon Camera Accessories ED 70 300 mm f 4 560 User Manual
Nikon Universal Remote MC 36 User Manual
Onkyo Laptop Docking Station DS A4 User Manual
Optimus Cassette Player SCP 85 User Manual
Optoma Technology Projector DX623 User Manual
Palsonic Flat Panel Television PDP 5000 User Manual
Panasonic Printer DP 3030 User Manual
Patton electronic Fan PPH3185 User Manual