Agri Fab Spreader 45 02141 User Manual

OWNERS  
MANUAL  
BROADCAST  
SPREADER  
Model No.  
45-02141  
BROADCAST SPREADER 100  
(PUSH)  
CAUTION:  
Read Rules for  
Safe Operation  
and Instructions  
Carefully  
Assembly  
Operation  
Maintenance  
Repair Parts  
PRINTED IN U.S.A.  
FORM NO. 47290 (REV. 12/01)  
 
D
B
C
A
E
H
F
G
J
K
L
I
P
N
Q
M
O
FIGURE 2 - HARDWARE PACKAGE  
KEY QTY.  
DESCRIPTION  
KEY QTY.  
DESCRIPTION  
A
B
C
D
E
F
7
2
1
1
3
3
9
1
Hex Bolt, 1/4-20 x 1-1/2" Long  
Hex Bolt, 1/4-20 x 5/8" Long  
Carriage Bolt, 1/4-20 x 3/4" Long  
Nylon Washer  
Flat Washer, 5/16" SAE  
Flat Washer, 1/2"  
I
J
K
L
M2  
N
O
P
1
1
1
2
Cotter Pin, 3/32" x 3/4" Long  
Flow Control Link  
Extension Spring  
Spacer Tube  
Cap  
Grip  
Vinyl Cap  
Hand Knob  
Handle Grip  
Hub  
1
1
1
2
G
H
Hex Lock Nut, 1/4-20 Thd.  
Cotter Pin, 5/32" x 2"  
Q
G
C
B
A
1/4" LOCK NUT  
1/4" x 5/8"  
1/4" x 3/4"  
1/4" x 1-1/2"  
E
D
F
5/16" WASHER  
FULL SIZE HARDWARE REFERENCE CHART  
NYLON WASHER  
3
1/2" WASHER  
 
5. Place a wheel onto the end of the axle that has a cross  
hole. The long end of the hub goes to the inside. See  
figure 5.  
ASSEMBLY INSTRUCTIONS  
TOOLS REQUIRED FOR ASSEMBLY  
(1)  
(1)  
(2)  
Pliers  
Hammer  
6. Assemble a 5/32" x 2" cotter pin through the notched  
wheel hub and the axle. See figure 5.  
7/16" Open or Boxed End Wrenches  
7. Lightly tap a hub cap onto the axle until it is snug  
against the wheel. See figure 5.  
1. Remove the spreader, the loose parts and the hard-  
ware package from the carton. Lay out parts and  
hardware and identify. Refer back to figures 1 and 2.  
2. With the spreader resting upside down on the top of  
the hopper, assemble a spacer and then a 1/2" flat  
washer onto each end of the axle. See figure 3.  
5/32" x 2"  
COTTER PIN  
HUB CAP  
AXLE  
SPACER  
CROSS  
HOLE  
WHEEL  
FIGURE 5  
1/2" FLAT  
WASHER  
FIGURE 3  
3. Placeawheelontotheendoftheaxlethathasnocross  
hole. The long end of the hub goes to the inside. See  
figure 4.  
8. Remove the 1/4" hex bolt, flat washer and hex lock nut  
from the center of the crossover tube. See figure 6.  
4. Place a 1/2" flat washer onto the axle and then lightly  
tap a hub cap onto the axle until it is snug against the  
washer and wheel hub. See figure 4.  
CROSSOVER  
TUBE  
NO CROSS HOLE  
WHEEL  
1/4" HEX  
BOLT  
SHAFT  
SUPPORT  
1/2" FLAT  
WASHER  
1/4" FLAT  
1/4" HEX  
WASHER  
LOCK NUT  
HUB CAP  
FIGURE 4  
FIGURE 6  
4
 
9. Place the handle tube (long) on the crossover tube,  
(side between crossover tube and hopper), align the  
holes in the handle tube, crossover tube, and shaft  
support. Assemble with 1/4" hex bolt, flat washer and  
hex lock nut removed in the previous step. See figures  
6 and 7. DO NOT TIGHTEN AT THIS TIME.  
HANDLE TUBE (LONG)  
1/4" x 1-1/2"  
HEX BOLTS  
10. Assemble two handle braces to the inside of the  
hopper frame, one each side, using two 1/4" x 1-1/2"  
hexboltsandtwo1/4"locknuts. Seefigure7. DONOT  
TIGHTEN AT THIS TIME.  
1/4"  
LOCK  
NUT  
11. Align the holes in the ends of the two handle braces  
with the hole nearest the middle of the handle tube  
assembly. Secure with a 1/4" x 1-1/2" hex bolt and 1/4"  
lock nut. See figure 7.  
12. Tighten all hex lock nuts and bolts, following same  
sequence as assembled in the previous three steps.  
See figure 7.  
LEG STAND TUBE  
VINYL CAP  
HANDLE TUBE (LONG)  
FIGURE 8  
HEX BOLT  
1/4" x 1-1/2"  
HITCH  
BRACE  
HEX BOLT  
1/4" x 1-1/2"  
15. Assemble the flow control link (the end with the small  
hole) to the flow control arm using one 1/4" x 5/8" hex  
bolt and one 1/4" lock nut. Do not over tighten. The  
flow control link must pivot freely. See figure 9.  
1/4" HEX  
BOLT  
16. Place the vinyl grip on the flow control arm. See figure  
9.  
1/4"  
LOCK  
NUT  
VINYL GRIP  
CROSSOVER  
TUBE  
FLOW CONTROL  
LINK  
FLOW  
CONTROL  
ARM  
FLAT WASHER  
SHAFT SUPPORT  
1/4" HEX  
LOCKNUT  
1/4" HEX  
LOCK NUT  
1/4" x 5/8"  
HEX BOLT  
FIGURE 7  
13. Assemble the leg stand tube to the handle tube (long)  
using two 1/4" x 1-1/2" hex bolts. Secure tightly with  
two 1/4" hex lock nuts. See figure 8.  
SMALLEST HOLE  
14. Place a vinyl cap over the end of the leg stand tube.  
See figure 8.  
FIGURE 9  
5